|
RE: Anyone have a NIB Inspire 60 4 Sale????
I need a cowl ! [&:] What a nice plane, I really enjoyed it
Posted on: 11/17/2011 6:40 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=10817328
RE: DLE 20 better exaust
Interesting thing is the TBM gadget, I wonder how it works and if it`s doable by myself ... [&:][8|][8|]
Posted on: 7/17/2011 6:43 AM by Author "Daniel Z"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10624889
DLE 20 better exaust
I`m thinking of a better DLE 20 exaust, I recently purchaced to replace a ys110, I only wish to have the best results and if possible without too much noise I have seen some older posts of some guys making a DIY beer can mufler, but I think it`s for bigger engines... or not? Thanks in advance Daniel Z
Posted on: 7/15/2011 7:10 PM by Author "Daniel Z"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10623157
RE: YS 110fz lacks of power
Ok, today I bench tested the engine again, with the new Orings and gaskets (and ring) 20% wildcat fuel 15x8 @ 9100-8800 (not stable) 16x4w @ 9900-9600 The only thing not looking good is the diaphragm, its not flat, a little bulged, anyway I can have decent transition Is this thing enough to steal my missing RPMs?, I know Chip said it does, but I want to know everyone experience Thanks, Daniel
Posted on: 2/24/2011 8:56 PM by Author "Daniel Z"
in the forum "YS Engines Support"
http://www.rcuniverse.com/forum/fb.asp?m=10361970
RE: YS 110fz lacks of power
No, I had about the same 8700 rpms before , that´s why I hoped an improvement with the ring replacement. Changing the valve cover gasket made it a little better (9000-9200 peak) I`m just over 500 ASL, have tried 30% while ago but I haven´t noticed changes in performance (dont remember tach readings) I thought my plane should be on the overpowered side at 7,7lb with this engine that`s why I`m scratching my head Will watch the rear disc also, thanks still4given Thanks again for everyone
Posted on: 2/21/2011 7:56 PM by Author "Daniel Z"
in the forum "YS Engines Support"
http://www.rcuniverse.com/forum/fb.asp?m=10354300
RE: YS 110fz lacks of power
Well , then I`m missing about 500 RPMs not 1000 as I thought, do you agree? I have a 16x4w and a 16x7 apc props , will replace the orings, change props, and tach the engine again I have a MAS 16x6 , Does it worth?
Posted on: 2/21/2011 4:52 PM by Author "Daniel Z"
in the forum "YS Engines Support"
http://www.rcuniverse.com/forum/fb.asp?m=10353782
RE: YS 110fz lacks of power
I`m using wildcat 20/20, the regulator diafragm seems a little distended but at 4k is ok and transition is good, I will try a new one anyway (thanks wcmorrison) I`m flying a 3,5kg or 7,7lbs plane (Aerokevlar Panther) and I want more power for vertical lines, and pulling out of torque rolls Seen posts of people with ys110`s puting 10k+ on a 16x4 or 15x8 is not unususal and is 20% more than mine! I will change orings too, Any ideas will be well recieved. Thanks for your help
Posted on: 2/21/2011 8:07 AM by Author "Daniel Z"
in the forum "YS Engines Support"
http://www.rcuniverse.com/forum/fb.asp?m=10352551
YS 110fz lacks of power
I have a Ys 110 working with good idle and transition but giving me about 8700 rpms with a 15x8apc, using new ring, so I`m a little disapointed Changed the valve cover gasket and improved to 9100 rpms , I still think It can be better , all the rest af the engine is very well mantainned any ideas? Daniel
Posted on: 2/21/2011 6:29 AM by Author "Daniel Z"
in the forum "YS Engines Support"
http://www.rcuniverse.com/forum/fb.asp?m=10352261
RE: P.Aerobatics Katana MD with OS 30 4 stroke
how much does it weight? power is enough? Prop 10x4 9x6
Posted on: 10/3/2010 11:39 AM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=10044339
RE: Fliton store
PM sent
Posted on: 9/24/2010 11:17 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=10025576
RE: Fliton store
wow ... my heart is touched and filled with 20/20 thanks to all of you
Posted on: 9/24/2010 11:15 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=10025572
RE: RIP, Mayhem......
This size has been taken by electric or gas recently, Maybe take a look to the 3D HobbyShop Viper Perhaps it is convertible to glow, also aeroworks have some 60-90 and 90-120 planes
Posted on: 9/23/2010 8:29 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=10023043
RE: Fliton store
Mainly the Cowl, secondary, wheel pants, wing tube, canopy and hatch. I can use other plane parts except for the cowl Man, I loved the plane, and there is no other 50-60 sized airplane I know of with similar performance Nostalgic pics... [:(]
Posted on: 9/23/2010 7:54 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=10022978
RE: Fliton store
I have tried Atlanta hobby and Advantage hobby, and there is no Fliton parts or planes there, any other place to search? Thanks
Posted on: 9/22/2010 7:39 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=10020566
Fliton store
I have readed some stories about fliton store, but now is the only place to buy some very needed parts for my broken inspire60, do I dare to buy or not? do you have any experience? Thanks Daniel
Posted on: 9/19/2010 10:22 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=10011054
RE: Fliton store
HELP !
Posted on: 9/19/2010 10:13 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=10013696
RE: Inverted Harrier...Words of wisdom??
Yep, p-Factor is much more accurate, thanks
Posted on: 5/28/2010 1:45 AM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=9764576
RE: Inverted Harrier...Words of wisdom??
Also, when you enter the inverted harrier to fly it in a straight line, automaticaly add a bit of left rudder (right when inverted) or you will fly in a circle to the left... why? because when you are inverted right thrust is LEFT thrust making torque worse, think about it, all planes I have flown do the same.
Posted on: 5/22/2010 10:01 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=9752410
RE: Knife edge Problem with Yak
Everyting points to a very aft CG, check also aileron neutral position (not "flapped", nor "spoileroned"), when you finish with these, mix the rest out
Posted on: 5/22/2010 9:40 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=9752356
RE: Fliton Inspire 60 Acro
I use a Saito 91 and it´s perfect for me! In your options I would choose the os 70 ultimate mainly because of weight, so, use also light equipment
Posted on: 1/20/2010 4:26 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=9432866
RE: What do y'all want?
Victor: Washout may take out wing rock but when you flip the plane wash out turns into washIN, so It may be better upright and worse inverted, I have done something very close to your objectives (avatar plane), and diferent airfoils on root and tip have taken all the wing rock out and if you have limitations on CF please use it in the landing gear because I think is where you can have greater savings in weight
Posted on: 1/9/2010 8:56 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=9402419
RE: What do y'all want?
I can recomend to you to use diferent airfoils in the root and the tip of wings, I had great sucsess with 12% root to 16% tip, this can make your plane stall the root first thus no tip stall and smooth harriers, and it allows you to taper the wing to have better roll rate and snaps, with big chord at the root and good taper you can easy achieve more than 700 sq/in in the surface Good luck!
Posted on: 1/9/2010 11:39 AM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=9401126
RE: What do y'all want?
Tall fuse for KE, legs installed on the bottom not in the middle of fuse to save weight, a 14-16% airfoil to fly slow but still glides, and the most difficult... wings capable of rock free harriers AND snaps
Posted on: 1/8/2010 11:07 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=9400210
Fliton inspire 60 CG
I´m a little confused about the CG on my inspire, it flys well but shows all the signs of a to forward CG (nose in at landing, inverted 45° needs correction, trim up for level flight, too flat upright harrier) but, I´m on the aft position recomended (about 6´) where are you balancing yours? Thanks!
Posted on: 11/12/2009 10:54 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=9249987
RE: Os Rotary engine
go for it ! it seems to have a very nice throtle response on the videos, and it is fairly light, just keep us posted!
Posted on: 8/3/2009 1:38 AM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=8985373
RE: Prop help please
16x4w APC for 3d or 15x8 APC for a mixed flight, I have also tested a 16x6 Mas, a 17`prop is too much
Posted on: 7/30/2009 1:00 AM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=8975547
RE: DEADSTICK NIGHTMARE!!
16x4 is too much prop! I use it in a YS110! try a 14x6 first
Posted on: 7/28/2009 1:13 AM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=8969844
RE: 3D setup recomendations
I say 12.25x3.75APC, 20/20 fuel and tower mufler! that`s what I use in my old 46fx with great success
Posted on: 7/19/2009 1:23 AM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=8945268
RE: How to GO LIGHT on this plane??
all TruBlu02 says, and use a 3A regulator with lipos, you can use 2s 700 mah (very light) reg at 6v means more speed and power for the servos, and you can charge at the field very quick, also it is possible to share lipos with rx and foamys as a foamy is much more stress for the lipo is good to test and check them that way. I have used 5-6 gms servos for throttle with no problems at all for years, just put them away from the engine anyway, In the landing gear is where you can save the most with CF
Posted on: 7/10/2009 2:52 PM by Author "Daniel Z"
in the forum "3D Flying!"
http://www.rcuniverse.com/forum/fb.asp?m=8922081
RE: Your biggest
I saw once Quique setting the radio for a new Ptihon 100cc, and he uses different expo (more to the right) I think it was because of P factor, to get the same feel on both KE, I know it is not a pattern plane but the guy sure knows how to setup a plane!
Posted on: 6/17/2009 8:27 PM by Author "Daniel Z"
in the forum "RC Pattern Flying"
http://www.rcuniverse.com/forum/fb.asp?m=8860478
| 
