|
RE: When's the 12X replacement coming?
Fitting a Spektrum 12 channel module internally would almost certainly contravene the BMFA's guidelines on modifying Tx's, which could result in the insurance becoming invalid if you have an accident. You could fit the Futaba 12 channel module for the MX22 which gives you all 12 channels. I've been using mine for jets for well over a year now with no issues. Roger
Posted on: 12/5/2011 6:40 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10844028
RE: RAF Honington Photos
Thanks for the pics Mark which are the first I have of my Hawk in the air. As usual with Vinny present there was a lot of banter[:)] Maybe see you again next week. Roger
Posted on: 8/22/2011 3:37 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10681228
RE: JetCat Start Problem
Mark, Sorry for the confusing statement, I meant that you can't change the value once the start sequence is underway. Roger
Posted on: 6/15/2011 6:20 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10575073
RE: JetCat Start Problem
of it I'll reduce the voltage. Roger
Posted on: 6/15/2011 1:48 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10574868
RE: FASST for JR?
MM You have to set your Tx to PPM and depending upon the model you can get up to 12 channels (MX22), but I believe the JR 9xxx and 10x series only provide 9 channels in PPM mode. If you need more channels, then an MX22, MX24 or Futaba Tx will be necessary. Roger
Posted on: 3/31/2011 12:50 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10434006
RE: FASST for JR?
I've been using one in my MX22 for 2 years without any issues at all and all my jets are using FASST Rx's. It gives you the best of both worlds, in that you keep the JR programming and have a solid 2.4GHz link. Roger
Posted on: 3/29/2011 1:30 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10429598
RE: New Scheme Ultra Flash Black/Silver/Orange
Glyn, That really does look good and I imagine very easy to see, so it will be quite a difficult choice between that and the Shui scheme. Roger
Posted on: 3/11/2011 11:13 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10393497
RE: dangerous Battery explosion
This attached thread is interesting and shows that some of the larger capacity NiMh batteries can potentially be a problem. It doesn't look like you were the only one Malcolm[:o] http://scalesoaring.co.uk/yabb/yabb2/YaBB.pl?num=1236112426/459 Roger
Posted on: 12/18/2010 3:20 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10204045
RE: Rookie 2 equipment location
Here are some pics of the installation in my old Rookie, that used a P80 and fixed thrust tube. At the time of the pictures I was using NiMH cells for the Rx and ECU, but later fitted LiPo's for the Rx, but kept the NiMH for the ECU. My CG was further back than the instructions say and I had to move the ECU pack as far rearwards as I could to get the CG as I wanted it. Roger
Posted on: 12/2/2010 8:17 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10171589
RE: Comp ARF BAE Hawk build thread
all[;)] Roger
Posted on: 12/1/2010 4:35 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10168810
RE: Comp ARF BAE Hawk build thread
Dave, Here is the CARF Hawk and full size and you can see the paint scheme on the model is quite wrong. I hope the pictures have uploaded[8|] Roger
Posted on: 12/1/2010 2:16 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10168701
RE: Comp ARF BAE Hawk build thread
not fitting the jet pipe, so hopefully the build will be simple[;)] Roger
Posted on: 11/29/2010 12:05 PM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10166767
RE: Rotating doors on Jet Legend Hawk,
Great idea. Any chance of a close up picture of the bracket, pivot and stop please? Roger
Posted on: 11/25/2010 5:01 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10158400
RE: Graupner Inspiration build thread-Flown
Dave, Yep Hawk arrived Thursday, so have plenty to do for the moment. Roger
Posted on: 11/21/2010 3:55 PM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10149915
RE: Graupner Inspiration build thread-Flown
Flew my Inspiration again today at Honington and since lightening the model with a new lighter tail pipe and smaller Rx batteries it really does go well. I've now turned down the Booster 80 from 165K to 163K max revs as the extra power isn't really necessary. Conditions weren't the best and rain eventually stopped play, but it was good fun while it lasted[:D] Roger
Posted on: 11/21/2010 3:08 PM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10149835
RE: Any JR guys using this?
Florent, The Mx22 transmits 12 channels in ppm mode so you get all 12 channels, although I'm not 100% sure if they are all proportional as I have used some as switched channels, eg. retracts, but I believe they are. I think that the 10X will only transmit 9 channels in ppm mode, so your choice of system is up to you. Roger
Posted on: 10/22/2010 7:01 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10085706
RE: Any JR guys using this?
Rick, I've been using a FASST module in my JR/Graupner MX22 for about a year in jets and electric models without any problems. I made the move so that I could get a 12 channel system for an outlay of about $150 and retain the Tx that I was used to, rather than spend a fortune on a new 12 or 14 channel Tx. Roger
Posted on: 10/22/2010 5:07 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10085661
RE: Viperjet Rrrready, P20 installed and running
Good to see the patio is complete Colin[:D] The Viperjet should be interesting when your P20 arrives. Roger
Posted on: 10/17/2010 2:40 PM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10074433
RE: Cermark
Mine is similar at elevators 35mm, ailerons 16mm and rudder at 25mm and the CG is set at 155mm from LE of wing. Roger
Posted on: 6/18/2010 4:22 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9810802
RE: Recuring problem Loosing brake pressure on landing
A secure solution is to fit a small piece of metal tubing where the brake line is likely to touch the wheel and normal brake line at either side of it. It's worked on three F16's that I know of. Roger
Posted on: 6/3/2010 6:57 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9777762
RE: Comp ARF BAE Hawk build thread
Here you Jeff. http://www.tailormadedecals.com/index.php?option=com_docman&task=cat_view&gid=20&Itemid=34 Roger
Posted on: 5/14/2010 5:12 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9732843
RE: Graupner Inspiration build thread-Flown
I have AT legs and their 75mm wheels, that are about 8mm proud of the surface, measured at the axle. The dry weight of the model is approx 7.9Kg. Roger
Posted on: 5/7/2010 12:03 PM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9717188
RE: Graupner Inspiration build thread-Flown
Great move Sandor as the wheels are currently quite proud of the wing surface and can't help increase drag. When will these units be available? Roger
Posted on: 5/7/2010 10:00 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9716948
RE: TURBINE CHOICE
[quote]ORIGINAL: GSR Or you might just want to wait a month or two for the new Purple P100. About the same size as the Merlin/Rabbit more thrust and JC quality. It will probably be a good one. Scotty [/quote] Is that wishful thinking, or fact[;)] If it's fact, that just what I've been waiting for[:D] Roger
Posted on: 3/16/2010 12:19 PM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9586781
RE: FEJ F-14 Maiden in the UK
Here are some more shots of the wing swing mechanism and flying shots. Roger
Posted on: 3/15/2010 6:38 PM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9584743
RE: FEJ F-14 Maiden in the UK
Here's a taster of it landing last weekend. Roger
Posted on: 3/15/2010 5:51 PM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9584614
RE: Graupner Inspiration build thread-Flown
I had some more flights on mine today at a misty, damp and cold Honington and am slowly getting it dialled in, although the CG is still too far forward for me and I'm going to move the batteries around to push it back a few more mm. With the Booster 80 now turned up to 163K it's vertical..., so that I can really enjoy it without my fingers freezing. Roger
Posted on: 2/7/2010 4:31 PM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9485105
RE: breaking decals
Hi Ralle, Excellent service as ever[:D] Regards Rger
Posted on: 1/29/2010 5:08 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9457740
RE: breaking decals
Hi Ralle, I've just done a test sample and mine are breaking up when I try to slide them off the backing sheet. They were for the 1/7 Airworld L39. Regards Roger Melville
Posted on: 1/28/2010 3:53 PM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9456208
RE: Any Futaba 2.4 users tried Orbit Powerjack?
I'm using one in my Graupner Inspiration, fed by a Powerbox Sensor Switch and two Lipo's. It's flown and appears to do what it says on the tin. No issues at all. Roger
Posted on: 1/26/2010 6:21 AM by Author "Roger M"
in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9448993
| 
