RE: 30cc Edge 540 build
Oh lawn boy gen 2 is mixed at 32:1, if I use the sthl syn may go to 40:1, 50:1, I read other posts where guys say they have been running that ams oil saber at over 100:1 Even with the lawn boy 32:1 the engine runs very well with a ton of power and is very reponsive. I would imagine a higher quality synthetic would run better at 32:1 than the lawn boy. A seized motor would possibly spell disaster and under lubricating atthose costs does not make sense to me to pick up a small amount of preformance. Ill probablly stay around 40:1 in the future. I hve heard alot of people complaining about DLE plugs. I ran a tank on the bench and in the plane with no complaints but just ordered a coupleNGK cm-6's off ebay for $1.99 off ebay sure beats 9.99 been seeing for the DLE plug. I have always had goodluck with NGK's.
Posted on: 12/3/2010 5:33 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10174526

RE: 30cc Edge 540 build
Hey thanks! When II ran it I did pop the wings on her, I could not resist! I think I will move the filter to the outlet on my fill tank one less thing to leak or plug. This is my firts gasser and going off what little I know and AW instructions. If the tank is clean and fuel is filtered prior to filling it should be clean. Plus carb does have a screen in it . I still need to order servos and extensions but most likley will wait till after xmas. IIts all pretty much ready to go other than servos and running servos extensions, pull pull set up, and final adjustments. I want to get a aluminum fuel line tee and get a different filler dot not to sure I like the one that it came wirh. This weekend I am planning on starting to build a set of skies for her. I made a set for my contender and found snow to be fun taking off and landing on. As far as oil goes I am breaking it in on lawn boy like DLE recommends and afterwards going to synthetic. I have been using the STHIL syn. inl my 2 stroke chain saw,red max leaf blower and snowblower for the last 6 years with great results. I left my Toro snow blower sit with gas in it last year (Bad me!) and it fired right up andran great today. The snow blower is 6 years old and still has same plug in it as well as leaf blower. I also like the belray hr-1 syn as well, its a few bucksmore I had ran it in my Honda cr 250 at 100:1 with no issues at all. I may try a few differentones to see what works the best. Any recommendations?
Posted on: 12/3/2010 5:20 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10174502

RE: 30cc Edge 540 build
Yes thats the battery! Seems like a nice battery. At the moment I do not have a voltage regulator installed. A friend of mine has been flying without one using a life bat. on the DLE ignition for over a year now with out any problems. I may buy one for security when she's ready for flight. As far as the DLE manifold (aka the muffler) goes I dont feel as if it is much louder compared to other pitts style mufflers, I was acually surprised by this. But pitts muffler looks alot nicer![;)]
Posted on: 12/3/2010 3:07 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10174255

RE: 30cc Edge 540 build
Bladebender I live in Elyria about 30 minutes west of Cleveland. I had a a couple hours free today so I decided to install fuel tank and lines. I just had to test it all out and make sure their were no leaks. I am impressed with the DLE30cc tons of power it will sling shot this plane through the air with ease. This is my first gas plane and love it, after I test ran everything no mess! I filled tank up about 3/4 and it ran for 23minutes while I slowly worked throttle. I also tested out a Life battery from EPbuddy.com with the ignition system. It is light weight and well made 2300Mah 6.6v. It was fully charged before I fired the DLE up. After 23 minutes of run time it only required 503Mah to put it back to a full charge. Looks like atleast 3-4 flights on one charge. Using a cell pro10 itonly takes15-20 minutes from dead to full. It was only 26.99 may get another to power the reciver. Heres a pic of what I did today, feel free to include your 2 cents if you guys see somthing you dont like or any ideas that may or may not be helpful! Thanks
Posted on: 12/2/2010 7:06 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10172910

RE: 30cc Edge 540 build
As far as using the stock muffler goes it does fit in the cowl. It leaves about 1/4" clearance from muffler to cowl, but you have to trim nore of the underneath of the cowl off to allow muffler tip to clear and vent outside cowl. Using the jtec pitts style you pretty much just have to trim for cylinder head to clear. As far as function goes stock muffler will work fine but it will not look as clean when finished using jtec or similar pitts style wrap around muffler. I will be ordering a Jtec for it eventually no rush to get her in the air as the Cleveland weather makes flying no fun.
Posted on: 12/1/2010 11:11 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10170964

RE: 30cc Edge 540 build
I have had a couple of days to fool around with this sweet lil plane. It was packaged well with a box in a box to keep it safe during shipping. When opened I found all was well with the contents. The covering is excellent with no major wrinkles or bubbles. I went over resealed everything but it really did not seem to need it, but after acouple days adjusting to my climate I did notice a few wrinkles appeared so I resealed and all is well. I would go on about how gorgeous this plane is but has already been covered by others! TThis is my first AW plane and I have no regrets. Thanks Airborne for the advice was not using my brain! JJust thought it looked clean but I am sure the heat would of killed the ignition module. As far as a wraparound muffler goes its a must have. The factort DLE muffler will work itwould just require more of the cowl to be trimmed for it to fit. This plane is very nice to look at so why mess with a good thing. Thanks again airborne hows this?
Posted on: 12/1/2010 6:19 AM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10168957

RE: 30cc Edge 540 build
Here is a picture of the DLE 30cc mounted up and ignition installation underway.
Posted on: 11/30/2010 10:37 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10168569

RE: 30cc Edge 540 build

Posted on: 11/30/2010 10:17 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10168553

RE: 30cc Edge 540 build
Looks like a really plane! I cant wait to get my hands on mine. Was hoping it woud show up today but its looking more like monday. Good luck with the build keep us updated and I will try to get some different angles from what you have to give others a full view of this beauty.
Posted on: 11/27/2010 4:57 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10163119

RE: 30cc Edge 540 build
Bladebender, I know I will be going for the 7985, I have plenty of time to get them! The weather here puts the flying on hold so I will have time to save up and bite the bullet on the servos. They are on the top of my xmas list! Igot the plane for my birthday which is one hell of a gift! So I really dont mind if santa passes me by on the 25th! I will post pics. as soon as it gets here just checkedthe tracking and its on the truck for delivery!
Posted on: 11/27/2010 10:48 AM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10162482

RE: 30cc Edge 540 build
Feel free to post at will! I am considering using hd power servos all around but not sure on their quality. Was considering following AW rec on hitec 7985's all around but they are costly. As far as batteries go I have 2 2300mah A123's. This will be my first gas plane as well as ARF (QB)) . This will be a big step up from my Top flite contender.I have flown a friends 50cc edge and it is a great flier! Id love to see pics.! Post away!
Posted on: 11/27/2010 12:44 AM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10161997

RE: 30cc Edge 540 build
Bemesen, Mine should be in my hands Sat. or Mon, FedX says its here in Ohio so it just depends on when it hits my sort facility. Would you recommend going with the AW spinner? I also will be using the xoar 19x8 prop. What kind of servos do you plan on using?
Posted on: 11/26/2010 10:38 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10161837

RE: 30cc Edge 540 build
Double checked and YES! It has a choke! Thanks! Just ran it today and it seems to be a strong runner. Fired up easily enough and with a few minor adjustments idles well and revs well.
Posted on: 11/25/2010 2:37 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10159333

RE: 30cc Edge 540 build
It will be powered by a DLE 30cc rear carb. From what I have heard this should be a great combination.
Posted on: 11/25/2010 1:27 AM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10158254

30cc Edge 540 build
Hello everyone, just recived shipping conformation from FedX that my new AW 30cc Edge 540 is on its way. 11/29/10 is the delivery date. I will be posting pictures of the packaging and everything inbetween. This will be my first AW plane as well as AFR so I hope to provide an accurate review as well. I will keep you all posted!
Posted on: 11/24/2010 5:43 PM by Author "bigjer12341" in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10157384