|
RE: 30cc Edge 540 build
Just have to be easy on the elevator and bring them in with a little speed. If you ask 100 different people you can get a 100 different answers. I like the way an edge flew just didn't like the way they landed.
Posted on: 8/28/2012 5:19 PM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=11209640
RE: 30cc Edge 540 build
I believe its just because its an edge 540. I have never had one that was not afraid to drop a wing. Mine flew great but at slow speeds or to hard a pull on the elevator and it would snap or drop a wing. Just my. 02cents worth. I know some guys swear by them but I would much rather fly an extra or a sukhoi.
Posted on: 8/28/2012 2:54 PM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=11209472
RE: NEW DLE30!
Ok its been a while with IMAC and work I finally got to work on my dle 30 increased plug gap to .024" no luck, on the ground it seemed to be ok but once in the air the miss would come back, played with the hall sensor still no luck. My next thought is to change out the ignition with a known good one which I have since I'm building a 3DHS extra with a dle 30 that I know does not have a miss.
Posted on: 6/27/2012 8:10 AM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=11133749
RE: 30cc Edge 540 build
Bad Brad graphics makes a very good graphics set for this plane.
Posted on: 4/30/2012 7:32 AM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=11062423
RE: NEW DLE30!
I'm going to start with gapping the plug at .024" and see if that helps.
Posted on: 4/17/2012 10:53 AM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=11045840
RE: NEW DLE30!
I have a problem with my dle 30 it has a pop to it from 1/4 to full throttle I have tried tuning it out with no luck changed the spark plug and gapped it a .018-.019 and just switched to Stil hp ultra 50:1 oil with no luck yet. I think I could have a timing issue does anybody have any thoughts on this.
Posted on: 4/17/2012 6:19 AM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=11045514
RE: 30cc Edge 540 build
Pitch the gasket and use high temp rtv silicone.
Posted on: 4/14/2012 3:40 AM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=11041262
RE: 30cc Edge 540 build
I used Hanger 9 metal arms ( the black ones) and they worked real good.
Posted on: 4/10/2012 3:37 PM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=11036661
RE: 30cc Edge 540 build
I used a xoar 20 x 6 with very good results, aand the same servos. For batteries I used Hobbico 2s life 2100 unregulated with no problems and just 4.8 nimh on the ingnition.
Posted on: 4/10/2012 4:35 AM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=11035712
RE: 30cc Edge 540 build
Go with the Aeroworks you will be very happy. The dle 30 fits but I had to use 1/4" spacers that came with my AW 50cc extra 300 to get the prop hub at the correct distance. If you do go with the AW edge when you mount the throttle servo make sure you leave enough room to get a hex wrench in there to tighten or loosen the stand off bolts. I found out the hard way that I mounted the throttle servo to close and I could not loosen the lower left bolt when it came time to take the dle 30 off.
Posted on: 3/20/2012 3:23 PM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=11008705
RE: 30cc Edge 540 build
Use a 4.8 jr sport 1500 and you will be fine. I use it on my edge with a dle 30 and after all day of flying when I charge the battery a week later it usually only puts 500 to 700 mah back in it. You don't gain any advantage of using a 6v battery and dle ignitions don't like them, it tends to let the smoke out of the electronic ignition.
Posted on: 1/10/2012 6:53 AM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10901572
RE: 30cc Edge 540 build
I believe channels 1 and 6 are for the ailerons and 2 and 5 are for the elevators.
Posted on: 12/22/2011 12:01 PM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10871751
RE: NEW DLE30!
I had the same problem. When I would do blender and come up on the power flame out. I talked to jedi jody at VVRC the master, and he told me to richen the low end even though I had good throttle transition, well it fixed the problem.
Posted on: 11/8/2011 10:17 AM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10802656
RE: NEW DLE30!
That would be the one.
Posted on: 8/20/2011 6:36 PM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10679385
RE: NEW DLE30!
I'll keep my dle's all 4 of them. The only problem I have had is with my 55 had to replace the membrane in the carb. but all that was is a trip to the lawnmower shop and walbro carb kit and ta da problem was gone. I just finished up my Pilot 30cc extra 260 with a dle 30 and ran the motor today, just a little rich on the high end but tons of power and it turned out to be nose heavy even with CF spinner and a sig tail wheel assembly.
Posted on: 8/19/2011 2:28 PM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10677818
RE: NEW DLE30!
You are going to the right spot. I had a similar problem with my dle 30, when doing a blender I would push down elevator and come up on the throttle when the flame out would happen like clockwork. The engine ran fine on the ground good transtion from low to high. Jody told me to richen the low end while other people said to tap and run the breather line inside the fuse, well the low end trick worked no more deadsticks. Jody told me that if you have to run the breather line inside the fuse you have an airflow issue with your cowl.
Posted on: 8/19/2011 6:06 AM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10677231
RE: 30cc Edge 540 build
Better watch routing your ignition wire through the exhaust pipes. I did it that way on mine and it took about 5 flights to burn through it. I zipped tied mine to the other stand off.
Posted on: 7/25/2011 7:14 PM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10638884
RE: Pulling all ar7000 receivers out of my planes!!!
Sure it wasnt the plane itself. I had a H-9 27% cap 232 and it was a handful, it lived up to its nickname of the cap snap. Get it to slow either while landing or in a loop, roll, etc and it would stall big time and would take a lot stick movement to get it back. Just a thought.
Posted on: 3/4/2011 3:39 PM by Author "greg palmer"
in the forum "RC Radios, Transmitters, Receivers, Servos, gyros"
http://www.rcuniverse.com/forum/fb.asp?m=10379181
RE: NEW DLE30!
Need help with engine issues possibly. I have a new dle-30 on a AW edge 30cc 540, gave its 1st flight today (great plane) on its 3rd flight I tried to do a blender and when I fed in some down elevator and started to come up on the throttle the engine died two seperate times. It will fly from skyline to skyline inverted with no problem, snaps no problem there either 4 point rolls same thing, just when I start to add throttle to flatten out the spin the motor gives out. While on the ground good throttle response from idle to full throttle. Does anybody have any suggestions.
Posted on: 3/3/2011 3:37 PM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10377227
RE: 30cc Edge 540 build
Well I just finished mine up today, now I can't wait for a good day to give it a maiden flight.
Posted on: 2/18/2011 1:58 PM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10346098
RE: 30cc Edge 540 build
Has anybody tried one of these with a OS 160 on the front. I am building one with a dle 30 but I have a 80 OMP edge with a OS 160 that is a little under powered and was thinking about the extra 300 when it comes out.
Posted on: 1/17/2011 7:12 AM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10269395
RE: 30cc Edge 540 build
That is on good looking spinner on the front. Was it pre cut and drilled from AW? I putting the same set up on my AE edge 540, dle-30 but I bought a 3" spinner from VVRC which was pre drilled. I tried to call AW today but they are closed until the 28th
Posted on: 12/27/2010 8:34 AM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=10220624
RE: NEW DLE30!
All I got to say is bring on the pictures, I can't wait to see what it will look like. I have already bought a dle-30 for and next month I plan on getting a pitts muffler, props and spinner from valley view rc.
Posted on: 9/29/2010 10:00 PM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10036883
RE: NEW DLE30!
clouddancer thanks for the info on that. I have been trying to decide on the extreme flight or wait on the aeroworks 30 cc extra 300.
Posted on: 9/26/2010 9:08 AM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10027787
RE: NEW DLE30!
Has anybody tried a dle 30 on a extreme flight 78" extra 300. If so how did it do?
Posted on: 9/22/2010 10:41 AM by Author "greg palmer"
in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10019521
RE: 30cc Edge 540 QB Sneak Preview
I like the new 30cc edge but I cant wait to see the 30cc extra 300. I have a AW 120 yak with a 120ax on it which I used to take 1st place at the Blue Grass IMAC in basic and I just maiden my AW 50cc extra 300 last week and fell in love with it. Bring on some pictures of the extras.
Posted on: 9/6/2010 12:21 PM by Author "greg palmer"
in the forum "Aero-Works Support"
http://www.rcuniverse.com/forum/fb.asp?m=9983828
RE: Building kits
I would like to build a omp yak or edge 47" cause i've had a lot of luck with there arf's, 2 kat 40's ( may they rest in peace) 67" fusion and 80" edge, but if there going to be out of stock for a long while I'll settle for a mojo. Thanks for the input on building kits.
Posted on: 1/25/2010 5:37 PM by Author "greg palmer"
in the forum "Profile and Fun Flying Planes"
http://www.rcuniverse.com/forum/fb.asp?m=9447362
Building kits
I've been building arf's since I started flying 5 years ago. Now I would like to build either a omp kit or a mojo 40 and was wondering about what tools, glues and other building stuff I might need and any tips that can help. Thanks Greg
Posted on: 1/20/2010 7:53 PM by Author "greg palmer"
in the forum "Profile and Fun Flying Planes"
http://www.rcuniverse.com/forum/fb.asp?m=9433455
RE: My OMP Edge 80
Thanks for the 411 on the hinges. I'm trying to get it ready for our Pro Bro this weekend but I think all I will have ready is my good ole Fusion.
Posted on: 5/18/2009 9:14 PM by Author "greg palmer"
in the forum "Profile and Fun Flying Planes"
http://www.rcuniverse.com/forum/fb.asp?m=8780183
RE: My OMP Edge 80
Has anybody used Robart hinges on all the surfaces and if yes how many did ya use. I'm starting to build my Edge tonight and the only hinges I have are 1/8" Robarts. On the website 1/8" should be used in .25 to .90 size models.
Posted on: 5/18/2009 7:40 PM by Author "greg palmer"
in the forum "Profile and Fun Flying Planes"
http://www.rcuniverse.com/forum/fb.asp?m=8779954
| 
