RE: what would you keep?
Keep the FG[:D] parts will always be there
Posted on: 7/2/2009 8:24 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8901986

RE: Need your experience
Hey try a HPI filter or a Firehammer filter best filter I ever owned...KN filters are not designed for 1/5 offroad use... IMO
Posted on: 5/26/2009 11:31 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8801555

RE: Finally got a Rampage!!! Baja will be in some pix too
[quote]ORIGINAL: Wicked!! You can also use fuel tubing. And yes the truck is very under powered. I can't do anything about that yet though. [/quote] Bro alls you need is a good pipe ......the 23cc is more than enough power to play with[:D] http://www.youtube.com/watch?v=zeMxlgL64aI ................Oh and that problem with your engine...try venting your gas cap
Posted on: 5/8/2009 4:43 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8752198

RE: Opinions please!!! New engine running crappy
heres some info [quote]1) Locate the low and high RPM jets on the side of the carb - they are usually marked with a L and a H. Turn both jets completely CLOCKWISE ( to the fully closed position). 2) Rotate the Low jet counter-clockwise to 1 and 1/4 turns open. 3) Rotate the High jet counter-clockwise to approx 1 and 3/8 turns open. 4) Now, start the engine. You may need to turn the Low jet slightly one way or the other for the engine to start. 5) Adjust the Low jet as desired until the idle is where you like it. Turning clockwise ("CLOSING" THE JET) will produce a higher idle, and counterclockwise ("OPENING" THE JET) will produce a lower idle (and eventually flood and the engine will kill, if you turn it too far). 6) Open the throttle lever to full blast. Adjust the High jet until you get maximum RPMs. Note: this will probably be REALLY LOUD. Listen for the highest-pitched whine to tell you where max RPMs are hit. AFTER YOU FIND THE MAX RPM SETTING, TURN THE HIGH JET COUNTER-CLOCKWISE ("OPEN" THE JET) APPROX 1/16TH OF A TURN TO ENSURE YOU HAVE SUFFICIENT GAS/OIL MIX TO COOL THE ENGINE PROPERLY. Note: The above are just general guidelines. You may need to adjust both the H and L screws once you begin driving, depending on engine loading, altitude, humidity, etc. The trick is to find settings that work well for you, and stick with them.[/quote]
Posted on: 5/7/2009 2:31 AM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8747613

RE: Finally got a Rampage!!! Baja will be in some pix too
check your coil gap[:D] are you getting spark?? was it running at any point?? new plug I got the Rampage MT and the 2x4 redcat Bajer Buggy.....couple upgrades and your good!!
Posted on: 5/7/2009 2:26 AM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8747599

RE: Uh Oh...I think I need a baja...
you forgot about the $500-600 you will need for upgrades after you find out which ones you need[:D] Welcome to the money pit!! The baja is a good vehicle...youll like it
Posted on: 4/30/2009 5:27 AM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8728171

RE: Why upgrades are needed!!
I think that companies that make RC cars should sell totally RTR upgraded versions..... As they find out their short commings... the future models should include the upgraded parts needed as a thank you to all the customers who did the infield on the go testing for them. Some people like to do their own work others dont......... I think it sucks when you spend $800-1000 on a vehicle only to find out you need another $500-600 in upgrades ...........................Nice Photos Teamchrome where you guys running Kent or Auburn??
Posted on: 4/27/2009 2:34 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8719613

RE: Nutech Thunderbolt II - Out of the box pics.
Couple of questions I just got to ask you Foxy..... do the steal drive gears still make that obsene constant jingly noise?? Is there still play in the clutch bell drive gear?? http://www.youtube.com/watch?v=d6wcXIJhGuw What tunepipe will work...only the Carson side pipe like before ??
Posted on: 4/27/2009 1:36 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8719473

RE: Engage Rc alloy wheels/beadloc rings
My purchases made through him have gone off without a hitch....I dont know about all this Universe drama but he sells on ebay too and sometimes you will find better deals on his items there I bought the Titan, a FS buggy and steel gears for the FS through him....all through ebay before he had a website....I got alot better deals
Posted on: 4/26/2009 4:17 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8716862

RE: 1/5 Scale RedCat Rampage Gas Buggy TT5
Nutech makes the Thunderbolt.....they quit smartech and started up the 1/5 for themselves
Posted on: 4/26/2009 1:34 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8716594

RE: 1/5 Scale RedCat Rampage Gas Buggy TT5
[quote]ORIGINAL: 46u [quote]ORIGINAL: hellya Nutch makes the Thunderbolt.....they quit smartech and started up the 1/5 for themselves [/quote] Any links? [/quote] here ya go http://www.nutechracing.com/
Posted on: 4/26/2009 1:34 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8716611

RE: 1/5 Scale RedCat Rampage Gas Buggy TT5
I just snagged up a decent deal...the 2x4 baja roller for Redcat for $499 no engine or radio...should have it next week ][IMG]http://www.hpibajaforum.com/RedcatRacing/Rampage2x4A.JPG[/IMG]
Posted on: 4/26/2009 1:26 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8716576

RE: 1/5 Scale RedCat Rampage Gas Buggy TT5
option parts/ hopups http://www.rampagehopups.com/category.sc?categoryId=6 I own the MT version....the 23cc produces plenty of power and torque ...you have to add a tunepipe to unleash the power!!
Posted on: 4/26/2009 1:20 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8716562

RE: 1/5 Scale RedCat Rampage Gas Buggy TT5
Sorry hopups http://www.rampagehopups.com/category.sc?categoryId=5
Posted on: 4/26/2009 1:18 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8716569

RE: Baja Skunkworks Roto-Start For The Baja And Others
do you still have to pay massive import Tax if they write it up as a Gift and $50 value
Posted on: 4/25/2009 6:26 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8714900

RE: Engage Rc alloy wheels/beadloc rings
[quote]ORIGINAL: Ballistic Lunacy [quote]ORIGINAL: Pro5thScaleDistributors Your right, but the problem is, there material is terrible compared to 6061 or higher here in the USA. They may say it's 6061, but I am positive it is well below standards. I am just sharing my opinion on the issue of there material that I have experienced first hand. [/quote] My experience of Chinese aluminium has been about the same as any other that I've come across, I've seen parts from many manufacturers fail, more so the ones that make a big deal out of 'billet' 6061. Like any manufacturer the Chinese are going to make parts to specification, if they are told to make it from 6061 or 7075 they will do that, if they are told make it as cheap as poss out of whatever they like and keep the cost low then they will also do that. I have examples of 3Racing and GPM parts which have lasted well over 10 years which have not failed and have not presented fitting problems, then I have USA/Canada parts which are the complete opposite. If a part is made in China for a western brand and is junk who do you blame? The Chinese that made it or the Company that specified its design and material requirements? People go to china to have things made on the cheap - who's fault is that? Do you think the manufacturer is going to do anything other then spec and risk loosing the contract with the company they are contracted to? You can find many examples of quality product to come out of China for various other western brands and then some absolutely appalling rubbish for other brands, the problem isn't because it was made in China, its because it was made to a specification that was lacking. [/quote] Thats a good point!!! Put them blame for shotty materials where it belongs.....not with the manufacturer
Posted on: 4/25/2009 6:17 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8714493

RE: Fs truck Or MCD clone ?
I own every vehicle mentioned in this thread. Smartech Titan has a 3 bolt head..you can not purchase any head kit and use it..... it wont work FS vehicles are ok.....the first thing to go will be your bearings and shock forks Redcats have a few weak areas also but the support of the aftermarket companies that support the baja are a big plus.....lots of parts and support
Posted on: 4/25/2009 4:45 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8714525

RE: Nutech Thunderbolt II - Out of the box pics.
Not available for retail sales yet still being reviewed.... I hope parts support come alot quicker than with the first model............I still can not get parts to my original T-bolt so it sits on a shelf[:@]
Posted on: 4/25/2009 4:44 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8714535

RE: Engage Rc alloy wheels/beadloc rings
[quote]ORIGINAL: SAVAGEJIM As much as I myself do not endorse Integy, in this case, I would strongly suggest the Integy beadlocks over Puff's rings, they are actually way cheaper and evern much better looking: But of course, as I always say with Integy stuff or any other extraordinarily cheap gear, do take them with a grain of salt and realize that you just mightt get what pay for. [/quote] Those are the beadlocks hndaman1 was refering to [quote]ORIGINAL: hndaman1 I'am not a huge fan of alloy wheels.. I had alloy beadlocs from "reputable hobby-centric business" and they bent [/quote]
Posted on: 4/25/2009 5:32 AM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8713535

RE: Engage Rc alloy wheels/beadloc rings
[quote]ORIGINAL: hndaman1 I thinking of trying out the beadlocs. I'am not a huge fan of alloy wheels.. I had alloy beadlocs from "reputable hobby-centric business" and they bent and these are just plain simple design what the doctor ordered ..and if they bed I'am only out a couple dollar ,not a couple hundred..[8|] [/quote] I hear ya Man
Posted on: 4/24/2009 9:30 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8712847

RE: Redcat 2x4 Buggy Pictures
Right on Clubin!!! I've got one with my name on it too:D and its getting the 26cc marine head with the DS cooling fins stuck in it
Posted on: 4/22/2009 8:16 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8706606

RE: DDM pipe vs clone pipe...
Most of the "Big mod US shops" you refer to are geared towards the Baja or vehicles that use the same partsas the Baja....tell smartech hes bad for the hobby he started 1/5 with a very good clone. 3-4 years ago, as far as 1/5 vehicles we had FGs or Firehammers/XTM/Travellers Traxxas to choose from that was about it. Now there as so many different models you cant count them on your fingers
Posted on: 4/20/2009 6:17 AM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8697837

RE: DDM pipe vs clone pipe...
[quote]ORIGINAL: Wicked!! Just buy the DDM and support the hobby. When you purchase "clones" you are in a sence taking away from the hobby. [/quote] What what???[:D][:D] Any 1/5 adds to the hobby.....We have so many different choices now compaired to 3-4 years ago
Posted on: 4/19/2009 4:30 AM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8694855

RE: DDM pipe vs clone pipe...
performance is the same...material is not as good...sound doesn't make a car go[:D]
Posted on: 4/17/2009 1:40 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8690146

RE: King Motor Baja Elite - Ebay UK Import - Overview
You guys in the UK get soaked with taxes[&o]...I have imported alot of 1/5 vehicles and parts from europe...not only did I get a 18% discount ( No VAT) but I never once haver had to pay a import tax
Posted on: 4/17/2009 1:37 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8690137

RE: Nutech Thunderbolt II - Out of the box pics.
[quote]ORIGINAL: mikeinoz I have just fitted up a Carson Titan pipe, fitted well just had to drill a hole for the front mount. I also brought the fuel pickup to the back of the tank by pulling the fuel tube thru the grommet, then cut of the excess hose so the fuel should be easier for the carby to suck in. [/quote] I used the same pipe for the first model works great [image]http://www.fg-hopups.com/images/00214.JPG[/image]
Posted on: 4/8/2009 1:44 AM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8660183

RE: Nutech Thunderbolt II - Out of the box pics.
I think if Nutech wants to be in the game.... they need to set a price equal to the Redcat 4x4 buggy around $700 or have different options like a roller alot of us pull the stock engines right off the bat or use our own radio equipment and servos. I like the new body does it fit on the older version Foxy?? Atleast the aircleaner has some coverage now!!
Posted on: 3/30/2009 3:41 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8631740

RE: Man, so many choices. What to do?
[quote]ORIGINAL: Bmr4life Komatsu is the same as Zenoah? [/quote] Yes it is...... http://www.icongrouponline.com/PR/Komatsu_Zenoah_Co_JP/PR.html
Posted on: 3/29/2009 4:28 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8628968

RE: Man, so many choices. What to do?
They have a smartech traveller which is the exact same vehicle as the firehammer ...its better.... it comes with the zenoah 23cc not the dtx motor[:D] I snagged one up from ebay for $190 plus ship look at ebay Item number: 270364523087 this is the seller they normally sell for $200-300 plus ship You have to add your own servos and radio system....this is a great deal for a new vehicle...just the 23cc zenoah cost like $200 new
Posted on: 3/29/2009 6:45 AM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8627940

RE: HELLO need some help in this department
another word for you...... 4x4 redcat rampage www.rampagehopups.com Every 1/5 vehicle made requires some type of hopup or add on to help make it last longer
Posted on: 3/23/2009 2:54 PM by Author "hellya" in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=8607946