RE: tunnel hull turning
Are you using a push pull system on the servo to outboard . I would use at least two 4/40 rods , anything else on a tunnel is just not good enough . Also you could try one of the octura M series props , most tunnels like them . Don't over prop the boat I would try some of the carbon filled props found on the OSE web site , cheap and they are already S&B ,they have the 440,442 carbon fiber props you can get both for around 5 or 6 dollars plus shipping . Fine one that works then get the equivalent metal prop .
Posted on: 7/20/2012 6:41 AM by Author "highflyerbill" in the forum "Speed - Electric"
http://www.rcuniverse.com/forum/fb.asp?m=11162310

RE: ESC issues caused by bec/servo need help!
When you used a separate batt. pack did you disconnect the red wire on the ESC to reciever plug if you didnot it will go crazy .
Posted on: 7/28/2011 6:07 AM by Author "highflyerbill" in the forum "Speed - Electric"
http://www.rcuniverse.com/forum/fb.asp?m=10642875

RE: Miss Geico 29 Catamaran
Would like a little advise . I have the Geico with a seeking 60 amp ESC X642 prop and www.aircapitolhobbies.com off set rudder . Everything else is stock . If I run two 3300 MAH 3s in paralle would I have a problem or should I just stick to 2s . Thanks for any help in advance.
Posted on: 6/28/2011 6:24 AM by Author "highflyerbill" in the forum "Speed - Electric"
http://www.rcuniverse.com/forum/fb.asp?m=10595999

RE: How much nitro will a 2 stroke take?
I've been out of racing boats for a number of years.When I was racing you eather ran at least 60% Nitro or you stayed home.I did not like to go much above 60% because I liked running caster oil and above 60% caster will not stay in solution.That said ,I've always found if you are killing the plug on every run you're to lean.If you deform the plug after a race that's OK as we always changed the plug after every run even if it looked good.You'ed use these used pluges to dial in the boat.
Posted on: 6/20/2011 5:10 PM by Author "highflyerbill" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10584210

RE: MX-3
Thank you very much.You'rs is a much needed service.
Posted on: 2/1/2011 6:23 AM by Author "highflyerbill" in the forum "Airtronics Support Forum"
http://www.rcuniverse.com/forum/fb.asp?m=10304479

MX-3
I need the manual for the MX-3 75mhz FM 3 ch. radio . If anyone can point me to it I thank you so much.
Posted on: 1/29/2011 3:19 PM by Author "highflyerbill" in the forum "Airtronics Support Forum"
http://www.rcuniverse.com/forum/fb.asp?m=10298389

RE: 2 or 3 ch. FM recievers
It's on 75mhz, I believe airtronics uses pos. shift , so any pos. shift receiver should work.Also JR should work,and I would think there are recievers out there that will work with pos or neg. shift , so if any one has one used cheap pm me.Almost all aftermarket manufactures on 72mhz work with any shift.
Posted on: 1/28/2011 11:09 AM by Author "highflyerbill" in the forum "Airtronics Support Forum"
http://www.rcuniverse.com/forum/fb.asp?m=10295669

RE: 2 or 3 ch. FM recievers
It's on
Posted on: 1/28/2011 11:00 AM by Author "highflyerbill" in the forum "Airtronics Support Forum"
http://www.rcuniverse.com/forum/fb.asp?m=10295650

2 or 3 ch. FM recievers
I have a MX-3 FM transmitter and I need a two or three ch. reciever for.Does anyone out there know what brands will work besides the three ch. asirtronics reciever , which I've been looking for used , but so far no luck . PS if anyone has something that will work and is willing to sell please PM me.
Posted on: 1/27/2011 6:56 AM by Author "highflyerbill" in the forum "Airtronics Support Forum"
http://www.rcuniverse.com/forum/fb.asp?m=10292439

RE: Great Planes SS Brushless Suggestions Please?ng to
The super sportster is a real nice flying plane with a 400 to 450 watt motor . If I were buying it I would go with a Turnigy TR 35-36c 1100 or theSK 35-42 1000 hope that helps a little.
Posted on: 5/11/2010 11:12 AM by Author "highflyerbill" in the forum "Electric Aerobatic & Sport Planes"
http://www.rcuniverse.com/forum/fb.asp?m=9725951