|
RE: Building a Crackerbox step by step with lots of pics!
Here a site on the latest project the building of a 1/4 scale Crackerbox [quote]http://www.mariosrcmodels.com/crackerbox.htm[/quote]
Posted on: 9/29/2009 12:08 PM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9133043
RE: Building a Crackerbox step by step with lots of pics!
Hi all >a lot of info on these page but me i would do the top sheeting in one sheet at a time with ca i say it for guy that been building boat a long time because it you mess up the you have more work on hand then you thing .And by using 30min min epoxy you have more time to move it around to fit it better. But it will be better if you use the two sheet made into one sheet.To do this is to lay the two top sheet on flat bench and arrange them so that the good side face up .now using wide tape tightly tape them together in 4-5 place them run tape down the entire center seam..now flip the joined sheet over and hinge them open .Now use 15-30 min epoxy in that joint and lay the top sheeting on the bench and wipe the seam clean off excess glue and let sit over night .Next is to glue the sheet to deck frame to do is to cut 20 pieces of tape about 8" long or so then sand the bottom of the sheet with 200 girt paper then clean now mix 30min epoxy ans brush cost top of frame then bottom of sheet now just lay the sheeting and tape it down you can add weights on center if need .allow to re over night >hope this help
Posted on: 9/28/2009 8:26 AM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9129416
RE: Building a Crackerbox step by step with lots of pics!
i can look at the main site in the usa at [quote]http://www.zippkits.com/[/quote]full of picture and they can hook you up with set up for your boat
Posted on: 9/27/2009 12:58 PM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9127439
RE: Building a Crackerbox step by step with lots of pics!
Hi all . CrackerboxSydney And you can get all boat part from here [quote]http://www.ozrcboatsupplies.com/[/quote] .The boat looking good
Posted on: 9/27/2009 9:06 AM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9127000
RE: Zippkit Easy-Vee Build.
Nooh look super well done give yourself a pat on the back for me
Posted on: 9/20/2009 9:59 AM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9109521
RE: Zippkit Easy-Vee Build.
[quote]ORIGINAL: steinersamuel Nooh, not trying to cluter ur thread. I was intreeged by ur autobailers. I've been runnin mine, and it's a real pain to get all the water out of this hull. I also saw you drilled the keel side of bulkhead 4. This will pay off huge for u, nicely done. I'm in the process of modding mine. Here's my rig. I fabed all the harware, except for the SBD setup. Nice job on ur project by the way, looks pristeen. You'll love this hull, it can be pushed further than you would think. GITÂ SOME!!!!! Sammy [/quote] Hi m8 the auto bailer work better if they are installer on the lower point of the transom this way when boat running the water go out the back of boat .here a good look at them [quote]http://www.rocketcityracing.com/tek9.asp?pg=products&specific=jrgpmrn0[/quote]
Posted on: 9/17/2009 11:04 AM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9103034
RE: Zippkit Easy-Vee Build.
[quote]ORIGINAL: nooh First coat of resin applyed to the hull, I had a pair of flush mounted water pick ups that I had laying around so I installed them too, Don't know if they will work first time ive use them ????? Over the week-end hope to seal the hull completely so then maybe next week can start the painting. [;)] Take care... Henry. [/quote] Hi m8 the boat look super .good job so far and the boat come out the water a lot and the nice flush mounted water pick ups will not get water into them i lost my engine with these but their good for slow boat ,and these are what i use now Water Pick-UP Outlet Gas Marine Boat G260PUM Gasoline and can be found on Ebay item 220466400712
Posted on: 9/17/2009 10:40 AM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9102975
RE: MY 50cc cracker box
[quote]ORIGINAL: ByronRC whoa! that's awesome. Where in the world did you find that engine? [/quote] On Ebay and info and part on the Kawasaki Engines TD048D-AS00 2 Stroke Engine TD048D from here [quote]http://www.partstree.com/parts/?lc=kawasaki_engines&mn=TD048D-AS00+2+Stroke+Engine+TD048D[/quote]
Posted on: 9/15/2009 11:13 AM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9097392
RE: MY 50cc cracker box
Thank for reply .I will up load more picture soon as i can.you see i has an accident with my F150 truck pick up and my left hand is broken and truck need $6000 of work
Posted on: 9/15/2009 11:12 AM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9097387
MY 50cc cracker box
Hello all i am building a cracker box from zipp kit with an Kawasaki Marine 50CC engine here some picture i also looking for some picture of itand i am looking for info on the engine Kawasaki Engines TD048D-AS01 2 Stroke Engine TD048D
Posted on: 9/12/2009 5:27 PM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9089997
RE: Building a Crackerbox step by step with lots of pics!
Hi all here some up date on my Zipp kit cracker box it now house an Kawasaki Marine 50CC engine here some picture i also looking for som info on the engine # TD048D-131340
Posted on: 9/11/2009 1:52 PM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9087128
RE: Building a Crackerbox step by step with lots of pics!
Hi all Sorry for late reply but i broken my hand and now just getting back .here the link for the steamer but it the 1200 watt model http://www.fingerhut.com/ProductGroup.aspx?offergroupxid=73658.And for the picture CrackerboxSydney i can send them to you if you send me email
Posted on: 8/27/2009 9:06 AM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9049018
RE: John Drain's newer PT Boat plans?
Hi m8 .i build two of his boat from plan and here the plan link http://www.pt-boat.com/shop/pub/.uqptkembgyiiprx/freeplans.zip also you can get it at info here http://www.pt-boat.com/shop/ just click categories then free plan and then add to cart then checkout
Posted on: 7/31/2009 9:55 PM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8980211
RE: Building a Crackerbox step by step with lots of pics!
Here more picture of my Zipp Kits boat
Posted on: 7/31/2009 9:42 AM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=8978560
RE: Building a Crackerbox step by step with lots of pics!
Hi m8 i been bending stringers into position with the use of steam .And here the way i bend wood my wood/stringers. first i draw and layout the line on paper the i put finish nail in 1/2 ply on the outside of line then i take a pvc pipe and cap one end then i put the wood into it then i use a 1300 watt monster steamer to steam the wood for 5Min then take it out and put it into the building jig and let dry over night or you can bend it on the boat and clamp it down it bean very easy .hope this help anyone ,here some picture of it.
Posted on: 7/31/2009 9:37 AM by Author "kennyach"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=8978541
RE: Royal 1 1/2 scale F4u-1D info help
Hi all Me just getting all wood item to start building my baby soon will post as i build
Posted on: 6/5/2009 6:51 PM by Author "kennyach"
in the forum "Kit Building"
http://www.rcuniverse.com/forum/fb.asp?m=8828703
RE: 1\8 Scale Dumas Hydro
been using it for year m8 and never have any thing go wrong yet .so i do not know what your talking about m8 .also see here http://www.rcgroups.com/forums/showthread.php?t=263239 and it was also use on the lady Linda launched 1999 .here the web http://www.comptonlbr.com/images/Lite-Ply2.pdf
Posted on: 6/5/2009 8:37 AM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8765596
RE: 1\8 Scale Dumas Hydro
advanced builder .It sound like a plan too me to put the screws on the rear hatch . And any picture of the screws thru transom into them 2 stringers that you did m8
Posted on: 6/5/2009 8:23 AM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8827287
RE: the unofficial home of the dumas dauntless
Here an nice Dauntless picture
Posted on: 6/3/2009 8:24 PM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8823520
RE: the unofficial home of the dumas dauntless
I see it come with littel boat .Boy my kit did,t have one then again no blueprint just the help from my friend WhiteWolf McBride here
Posted on: 6/2/2009 8:51 AM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8819038
RE: the unofficial home of the dumas dauntless
Look what i found on Ebay .a Rare 1970 dumsa dauntless ,here the link # 360159477312
Posted on: 6/1/2009 9:58 PM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8817965
RE: the unofficial home of the dumas dauntless
Hello all . As some of you here know i working without blueprint sheets .So here where you pro come in .As i was reading it say to plank the bottom with two big sheet which is done from rib 7 to the transom .So now i need to know how the front plank go on i see their bigger then the rib and plank c go about 4-5 " in front of the boat , Any help would be nice .Thank again all
Posted on: 6/1/2009 9:43 PM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8817930
RE: the unofficial home of the dumas dauntless
Hi all .yep steaming the sprue chine meke to job go esaly .So now i make a mold to steam the transom
Posted on: 6/1/2009 9:43 AM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8815980
RE: Coast Guard Patrol Boat
<meta content="text/html; charset=utf-8" http-equiv="Content-Type"><meta content="Word.Document" name="ProgId"><meta content="Microsoft Word 12" name="Generator"><meta content="Microsoft Word 12" name="Originator"><link href="file:///C:\DOCUME~1\Admin\LOCALS~1\Temp\msohtmlclip1\01\clip_filelist.xml" rel="File-List" /><link href="file:///C:\DOCUME~1\Admin\LOCALS~1\Temp\msohtmlclip1\01\clip_themedata.thmx" rel="themeData" /><link href="file:///C:\DOCUME~1\Admin\LOCALS~1\Temp\msohtmlclip1\01\clip_colorschememapping.xml" rel="colorSchemeMapping" /><![if gte mso 9]> <![endif]><![if gte mso 9]> <![endif]><![if gte mso 10]><![endif]> <meta content="text/html; charset=utf-8" http-equiv="Content-Type"><meta content="Word.Document" name="ProgId"><meta content="Microsoft Word 12" name="Generator"><meta content="Microsoft Word 12" name="Originator"><link href="file:///C:\DOCUME~1\Admin\LOCALS~1\Temp\msohtmlclip1\01\clip_filelist.xml" rel="File-List" /><link href="file:///C:\DOCUME~1\Admin\LOCALS~1\Temp\msohtmlclip1\01\clip_themedata.thmx" rel="themeData" /><link href="file:///C:\DOCUME~1\Admin\LOCALS~1\Temp\msohtmlclip1\01\clip_colorschememapping.xml" rel="colorSchemeMapping" /><![if gte mso 9]> <![endif]><![if gte mso 9]> <![endif]><![if gte mso 10]><![endif]><![if gte mso 9]> <![endif]><![if gte mso 9]> <![endif]><meta content="text/html; charset=utf-8" http-equiv="Content-Type"><meta content="Word.Document" name="ProgId"><meta content="Microsoft Word 12" name="Generator"><meta content="Microsoft Word 12" name="Originator"> </meta></meta></meta></meta></meta></meta></meta></meta></meta></meta></meta></meta>
Posted on: 5/30/2009 12:13 PM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8811314
RE: the unofficial home of the dumas dauntless
Hello all here what i did so far .i bukid the frame and now i am putting the 1/4 sq on the side so i made a steam pipe bend the wood it only take 5min to do but look super ,here some picture of it .and the this is my shop it a 10ft x 17 ft room just for me ,thank to my wife
Posted on: 5/30/2009 8:55 AM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8811005
RE: Coast Guard Patrol Boat
Real nice boat to build .look like i going to build one after i done with my dumas dauntless.And here a link for the plan on Ebay http://cgi.ebay.com/Plans-for-US-COAST-GUARD-PATROL-BOAT-CAPE-class_W0QQcmdZViewItemQQ_trkparmsZ72Q3a1205Q7c66Q3a2Q7c65Q3a12Q7c39Q3a1Q7c240Q3a1318Q7c301Q3a1Q7c293Q3a1Q7c294Q3a50QQ_trksidZp3286Q2ec0Q2em14QQhashZitem19b419c398QQitemZ110395769752QQptZRadioQ5fControlQ5fVehiclesQQsalenotsupported
Posted on: 5/28/2009 9:35 PM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8807400
RE: the unofficial home of the dumas dauntless
WhiteWol me i use the scroll saw most of the time and also use the coping saw . OK today i started the boat first i re make the keels in one unit out of Birch aircraftplywood instead of splice two part together to form one Mod edit - removal of classified ad
Posted on: 5/20/2009 3:09 PM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8754665
RE: the unofficial home of the dumas dauntless
Hi all So how i have the ideal to use one KB 7.5 with twin drive that i will make myself or two kB 40 I will start to build the boat this week ,and happy holiday to all
Posted on: 5/19/2009 9:48 PM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8783185
RE: the unofficial home of the dumas dauntless
Sorry about that mop up for mock-up you see i have two hearing aid and some time i spell like i say it been like that from when i was 7 year old
Posted on: 5/19/2009 9:43 PM by Author "kennyach"
in the forum "RC Scale Boating"
http://www.rcuniverse.com/forum/fb.asp?m=8754655
RE: SI Mini.
Thank crispyspa m8 will check it out
Posted on: 5/19/2009 9:29 PM by Author "kennyach"
in the forum "RC Airboats"
http://www.rcuniverse.com/forum/fb.asp?m=8783127
| 
