|
RE: H9-F6F Hellcat 60 ARF
CRG I wasn't paying enough attention to the arf manual...forgot to include the joiner wire first...snafu..I also did not recess the hinge center into the control service..don't want to pull them off again sooo guess I can place some tape on each side to help tighten the gap.
Posted on: 11/16/2009 12:26 PM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9257721
RE: H9-F6F Hellcat 60 ARF
I just finished sawing off my ca glued elevators and re-attached them with dubro hinged pins. Its the first time doing this. The elevators work fine..all the hinges are swinging good and are tight...however the gaps are +- 1/8 inch along the control surfaces. Is the gap to big..if so whats the right way to close it. Thanks for your advice. MrSand.
Posted on: 11/16/2009 8:00 AM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9257225
RE: gluing pinned hinges
Thanks for the advice .... I will fit each hinge in the elevator slot...fill the lateral voids with thin balsa...vaseline the pin....scar the hinge face...epoxy it in...let it dry..then fit it to the stab next day...I have already prefitted both sides and marked the control surface for alignment. Once again thanks for the help. Mr.Sand
Posted on: 11/13/2009 7:35 AM by Author "mrsand"
in the forum "Tips & Techniques"
http://www.rcuniverse.com/forum/fb.asp?m=9250459
RE: H9-F6F Hellcat 60 ARF
ok thanks, I'm sure you fellows know more than me.... The tank is a little higher than the carb since I inverted the saito. If I keep it to two lines how do I keep the system from flooding when I fill. Sorry for my ignorance MrSand
Posted on: 10/10/2009 4:28 PM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9162053
RE: H9-F6F Hellcat 60 ARF
I have a fuel system question. I have mounted a Saito 100 with the valve covers down and left at +- 45 degrees. What tank/fuel line setup is recommended...one person says a three line...others a two line setup. I have a dubro fuel valve I was considering using. I appreciate any help I can get. Thanks. MrSand
Posted on: 10/10/2009 7:30 AM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9161227
RE: H9-F6F Hellcat 60 ARF
I also think that Navy0968's Hellcat is an outstanding looking scale model. The detailing is beautiful. Hope you can fly her soon. MrSand
Posted on: 9/18/2009 7:59 AM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9105150
RE: Clipped wing cub 48
The 56 will do the job,, just like the man said...slow and easy...swing around .... touch and go... learn to slip a little..its all fun Mr.Sand
Posted on: 8/27/2009 8:39 PM by Author "mrsand"
in the forum "RC Scale Aircraft"
http://www.rcuniverse.com/forum/fb.asp?m=9050483
RE: H9-F6F Hellcat 60 ARF
bignasty, sounds like a good method thanks MrSand
Posted on: 8/27/2009 8:35 PM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9050471
RE: H9-F6F Hellcat 60 ARF
Corsair Jock Thanks for the advice...I already have the radial glued in though I sort of mangled the area near the prop washer..its not as long as it should be...the tube idea is great..I am also going to install a external glow attachment. thanks for the ideas. MrSand
Posted on: 8/26/2009 1:11 PM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9046782
RE: H9-F6F Hellcat 60 ARF
appreciated. MrSand
Posted on: 8/24/2009 4:19 PM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9041092
Clipped wing cub 48
I have bought a World Models Clipped wing cub63 inch wing span. I also bought a 56 Saito 4S for power. I don't plan to hot rod the plane but I want enjoy the general acrobatics this design is capable of....Have I bought the right motor? Thanks for your comments. Mr.Sand
Posted on: 8/24/2009 4:08 PM by Author "mrsand"
in the forum "RC Scale Aircraft"
http://www.rcuniverse.com/forum/fb.asp?m=9041058
RE: H9-F6F Hellcat 60 ARF
, or comments. This assembly project is moving slow while I gain experience flying. Thank you. Mrsand
Posted on: 5/27/2009 10:31 AM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=8802507
RE: Thottle setup
thanks for the advice W8ye, redfox435, Graybeard... is there any reason why the slide through and screw (ala quick connector ) can't be on both ends?
Posted on: 5/16/2009 4:49 PM by Author "mrsand"
in the forum "Questions and Answers"
http://www.rcuniverse.com/forum/fb.asp?m=8774242
Thottle setup
Hello to all I was considering using a dubro cable with quik connectors at both ends on my throttle setup for a hellcat 60 arf ..does that work well or is there something better? Advice would be appreciated. Thanks MrSand
Posted on: 5/15/2009 8:31 PM by Author "mrsand"
in the forum "Questions and Answers"
http://www.rcuniverse.com/forum/fb.asp?m=8772344
RE: H9-F6F Hellcat 60 ARF
Hello to all I was thinking of making my thottle set up real simple on the Hellcat... using a dubro throttle cable and a ez connector on both ends..does anyone have any better way other than using standard pushrods.. MrSand
Posted on: 5/15/2009 8:11 AM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=8770672
RE: hangar 9 hellcat 60-fueling system
thanks for the advise fellow rc pilots I appreciate it....is there any reason why a T crossover and a fuel dot won't work properly? What happens when the tank is being filled..is there a chance the engine floods? I assume a setup locates the fuel dot about tank C/L or slightly higher on the cowel...is that about right? MrSand
Posted on: 4/26/2009 4:10 PM by Author "mrsand"
in the forum "Questions and Answers"
http://www.rcuniverse.com/forum/fb.asp?m=8716859
hangar 9 hellcat 60-fueling system
Can anyone give me a ideal of a better fueling system than a plastic T with fuel dot for fueling/defueling this bird? I"ve heard of one way valves and other things..Any help would be appreciated.. Mr.Sand
Posted on: 4/25/2009 8:39 PM by Author "mrsand"
in the forum "Questions and Answers"
http://www.rcuniverse.com/forum/fb.asp?m=8715179
RE: H9-F6F Hellcat 60 ARF
Ok, Thanks Wulf I appreciate your help. I googled fuel dots/valves an there is all sorts of interesting gagets. But a third line off the main tank to a fixed position on the fuse seems the most cost efficient MrSand
Posted on: 4/21/2009 8:42 PM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=8703256
RE: H9-F6F Hellcat 60 ARF
Thanks Wulf and Apcud7 for your idea's I can see the fuel tube on your plane Wulf Do either of you see any problems with the tank C/L being 40mm higher than the spray bar on the carb?
Posted on: 4/21/2009 12:25 PM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=8701845
RE: H9-F6F Hellcat 60 ARF
.. is there a better way. As always I appreciate any help or advice.. Thank you. MrSand
Posted on: 4/21/2009 7:50 AM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=8701268
RE: engine mounting TTPro40
I fixed the problem..I used a different spinner backplate..all is well thanks
Posted on: 3/29/2009 12:54 PM by Author "mrsand"
in the forum "Club 40"
http://www.rcuniverse.com/forum/fb.asp?m=8628635
engine mounting TTPro40
I'm finishing up another SRII and with the pinched cheeks the back plate for the spinner hits the cowl edge. The directions show the engine mounting 109 mm forward of the firewall! Is the measurement to the outer side of the drive hub or to the outside of the spun on prop retainer and nut? any help is appreciated. Mr.Sand
Posted on: 3/29/2009 12:15 PM by Author "mrsand"
in the forum "Club 40"
http://www.rcuniverse.com/forum/fb.asp?m=8628517
RE: Radian Problem..bec/batttery
I seem to have solved my problem...I re-binded the receiver and I have control of the servos now....only thing now is the trim adjustment which worked for a mintue quit on the rudder...the rudder works but no trim adjustment.....don't know what to say
Posted on: 3/27/2009 11:41 PM by Author "mrsand"
in the forum "RC Gliders, Sailplanes and Slope Soaring"
http://www.rcuniverse.com/forum/fb.asp?m=8624159
RE: Radian Problem..bec/batttery
I mis-spoke about the radian problem...what the thread shoud say is Radian Problem ESC/Battery
Posted on: 3/27/2009 8:41 PM by Author "mrsand"
in the forum "RC Gliders, Sailplanes and Slope Soaring"
http://www.rcuniverse.com/forum/fb.asp?m=8623415
Radian Problem..bec/batttery
This is a new RTF...I turned on the transmitter then pluged in the battery last night and I had control of the servos and motor. Tonight I was doing a final mock up and nothing works after turning on the trans...then plugging in the charged battery!!! The bec signals a tone then beeps 3 times when it attached to the battery,...but I have no control from the trans. anybody have suggestions
Posted on: 3/27/2009 7:55 PM by Author "mrsand"
in the forum "RC Gliders, Sailplanes and Slope Soaring"
http://www.rcuniverse.com/forum/fb.asp?m=8623212
RE: New Radian
Thanks for the advice, I will tie into the existing threads MrSand
Posted on: 3/26/2009 8:47 PM by Author "mrsand"
in the forum "RC Gliders, Sailplanes and Slope Soaring"
http://www.rcuniverse.com/forum/fb.asp?m=8620079
New Radian
Motor Sailors I recently bought my first sailplane...a Radian RTF.... I have rc experience...but would appreciate any tips about flying this plane or setup..I realize its suppose to be ready...but I thought I would check with owners anyway...thank you in advance MrSand
Posted on: 3/26/2009 7:53 AM by Author "mrsand"
in the forum "RC Gliders, Sailplanes and Slope Soaring"
http://www.rcuniverse.com/forum/fb.asp?m=8617940
RE: H9-F6F Hellcat 60 ARF
Thanks for the pictures Tom2Bell I will probally saw off the offending screw and liquid lock it MrSand
Posted on: 3/18/2009 8:55 PM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=8592263
RE: H9-F6F Hellcat 60 ARF
Tom2bell I guess I could do that but how did you secure the screw so that it would effectively hold like the others? Steve
Posted on: 3/17/2009 9:02 PM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=8588803
RE: H9-F6F Hellcat 60 ARF
MrSand
Posted on: 3/17/2009 5:40 PM by Author "mrsand"
in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=8588186
| 
