RE: engine sugestion for 110
. Thanks nextofkin
Posted on: 9/14/2012 10:03 AM by Author "nextofkin" in the forum "Giant Scale Aircraft - General"
http://www.rcuniverse.com/forum/fb.asp?m=11228422

RE: engine sugestion for 110
Also the RPMs are with the 18 X 6 was 6900 rpm and the 16 X 8 went to 7400 rpm maybe I'm expecting to much from this plane, I was looking at the Aero Works Cub and it has a 110" wing weights 19lb. to 20lb. and thay suggest a 50cc to 55cc engine. Thanks nextofkin
Posted on: 9/13/2012 10:16 AM by Author "nextofkin" in the forum "Giant Scale Aircraft - General"
http://www.rcuniverse.com/forum/fb.asp?m=11227351

RE: engine sugestion for 110
The prop size that I have tried are 18 X 6 XOAR and a 16 X 8 Master Airscrew flew the same with both. The 40cc is a SPE 40cc engine that weights about 1/2 lb. less than the Homelite I also have a SV 26cc that might be better because of the size of the prop, 40cc = 20" prop verse a 26cc = 18" prop. Need more power and lighter weight motor. Thanks nextofkin
Posted on: 9/13/2012 9:44 AM by Author "nextofkin" in the forum "Giant Scale Aircraft - General"
http://www.rcuniverse.com/forum/fb.asp?m=11227319

engine sugestion for 110" cub
I have a 110" wing span Cub, it weights 18 lb. right not it has a 26cc Homelite in it but you have to fly it wide open. It looks like it is struggling until it picks up a little speed witch is not much. What would be a good gas engine in cc? I have a 30cc, a 38cc, and a 40cc to pick from but am leaning to the 40cc. Thanks nextofkin
Posted on: 9/12/2012 10:29 AM by Author "nextofkin" in the forum "Giant Scale Aircraft - General"
http://www.rcuniverse.com/forum/fb.asp?m=11226244

RE: Welcome to Club SAITO !
Sharpeye22 You might have thought of this, if you have the old bearings measure the old one and compair it to the new one. Hope this helps nextofkin
Posted on: 7/4/2012 1:39 PM by Author "nextofkin" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=11142968

RE: Hangar-9 Sopwith Camel Build Thread
Mustang Fever: Could you measure the rotary engine diameter from head to head. Need a rotary engine to go in a cowl with a 4.5" hole. Thanks nextofkin
Posted on: 3/26/2012 9:37 AM by Author "nextofkin" in the forum "ARF or RTF"
http://www.rcuniverse.com/forum/fb.asp?m=11015655

RE: ESM LA-7 From VQ Warbirds
Has anyone used a Zenoah G-38?
Posted on: 2/27/2012 6:19 AM by Author "nextofkin" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=10978003

RE: ESM LA-7 From VQ Warbirds
What engines are you guys using I have herd of everything from 26cc to 55cc and everything between. I have a Zenoah G38 and wonder if this will fly this plane like its suppose to and not be a dog. Thanks nextofkin
Posted on: 12/26/2011 1:17 PM by Author "nextofkin" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=10876932

RE: Has anyone tried the new PTE36R ?
I agree with you Ibcinyou mud slinging does not belong here it's for info "ONLY". Did you get the muffler problem fixed? I am looking at this engine for a ESM LA-7 does anyone know how it will fly this plane I will call you around the first of the year about a engine unless you have a sale before then. He! He! nextofkin
Posted on: 12/6/2011 8:22 AM by Author "nextofkin" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10845980

RE: Hangar-9 Sopwith Camel Build Thread
A Sopwith Camel is for sale at K.C. Hobby in Archdale, N.C. looks good has servos, price was $200. Nextofkin
Posted on: 10/12/2011 6:55 AM by Author "nextofkin" in the forum "ARF or RTF"
http://www.rcuniverse.com/forum/fb.asp?m=10761307

RE: Welcome to Club SAITO !
AmishWarloard What kind of program are you using in your post with the laptop and where did you get it? Thanks Nextofkin
Posted on: 8/27/2011 3:55 PM by Author "nextofkin" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10689716

RE: Hangar-9 Sopwith Camel Build Thread
Has anyone put a RCGF 15cc engine on this plane if so what problems did you have Thanks nextofkin
Posted on: 7/10/2011 6:52 AM by Author "nextofkin" in the forum "ARF or RTF"
http://www.rcuniverse.com/forum/fb.asp?m=10614466

RE: RCGF Engines
or 45cc will be it. Thanks nextofkin
Posted on: 6/24/2011 6:41 AM by Author "nextofkin" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10589953

RE: RCGF Engines
Not looking for 3D but would like to do standard aerobatics (loops, rolls, fly upside down, stall turns, normal war bird maneuvers) and still have power to get out of trouble. Before it is said I know this is not a war bird. It will weight about 16lb. Thanks nextofkin
Posted on: 6/23/2011 10:15 AM by Author "nextofkin" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10588507

RE: RCGF Engines
Could anyone sugest a RCFG engine for a Great Planes Giant Big Stik thay sugest a 25cc to 35cc engine would the 26cc fly it like it should or do I need the 32cc ? I have a RCGF 26cc on a Hanger 9 PT-19 but it's not broke in yet so can't compaire. Thanks nextofkin
Posted on: 6/23/2011 8:29 AM by Author "nextofkin" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10588319

RE: cc of Homelite
are talking about airplane only engines not conversions. nextofkin
Posted on: 6/18/2011 11:04 AM by Author "nextofkin" in the forum "Engine Conversions"
http://www.rcuniverse.com/forum/fb.asp?m=10580491

cc of Homelite
How do you tell the cc of the Homelite blower engine without taking it apart? I know it comes in 25cc and 30cc but witch one? model number 08017G seral # HSZ961627 BP-250 Thanks nextofkin
Posted on: 6/16/2011 10:25 AM by Author "nextofkin" in the forum "Engine Conversions"
http://www.rcuniverse.com/forum/fb.asp?m=10577164

RE: Tower Hobbies .46 Engine
It's a Hanger 9 PTS P-51 yellow tail, I've flew it before but I pancake it on a landing and distroyed the fuselage just reorder a fuselage and put it back together, ran it today on a 10.5X6 prop idle 3150rpm low end 12000rpm top end tried to tweak the low end and throttle to get idle down to 2500rpm but it kelp cutting off 3150rpm seams the best. nextofkin
Posted on: 5/26/2011 10:23 AM by Author "nextofkin" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10541641

Tower Hobbies .46 Engine
What would be a good prop for the Tower Pro .46 on a P-51 mustang and does any one know the low speed settings for the carb. is it set with it closed or open Towers web site said 2mm but that seams a little large I'm open for suggestions, please help. Thanks nextofkin
Posted on: 5/25/2011 10:25 AM by Author "nextofkin" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=10539883

RE: GP Slow Poke 40 to electric
I also have a Slow Poke .40 in kit form and was thinking of electric. Seen a video of one and it look like it flew very well, a 2200 mha battery 3 cell and a AXI 2826/12 motor was used, weight had to be added in the nose to balance so why not add another cell make it a 4 cell battery about 2800mha or 3000mha to help with weight and more power. Just a thought nextofkin
Posted on: 12/19/2010 10:44 AM by Author "nextofkin" in the forum "Glow to Electric Conversions"
http://www.rcuniverse.com/forum/fb.asp?m=10206268

RE: Welcome to Club SAITO !
you can always put jb weld around the end if you run a silicon extension I use it all the time. nextofkin
Posted on: 5/30/2010 11:47 AM by Author "nextofkin" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=9768890

RE: Welcome to Club SAITO !
Thanks Retransit What does it weigh, and what canopy did you use? The PT-26 looks good. I've thought about that but finding a canopy that fits is something else. Thanks nextofkin
Posted on: 3/25/2010 11:59 AM by Author "nextofkin" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=9610810

RE: Welcome to Club SAITO !
or sonething else? nextofkin
Posted on: 3/24/2010 12:51 PM by Author "nextofkin" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=9608141

RE: Welcome to Club SAITO !
Thanks for help. I would like to thank NM2K for the sugestion he gave me on my Saito 1.20. I went with a APC 15X8 prop, idle rpm is 2400 to 2500 top end is 8700 to 8800 rpm the reason that I did not think of the prop size was I am about the third owner of this plane and engine and this is what was used by everyone else. The APC 15X8 weights at 3.20 oz. and the Zinger 16X8 at 1.65 oz. I think the reason for the lower rpm (was weight)( fly wheel affect) but you think that it would turn more rpm for lighter weight but it works so thank you ED. William
Posted on: 8/16/2009 9:33 AM by Author "nextofkin" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=9020019

RE: Welcome to Club SAITO !
I have a Saito 1.20 and I'm have a hard time with it. Have several questions so please answer by number. 1) What rpm is the max it should turn, 16X8 zinger prop with power master 15% fuel, this engine has new bearings and a new piston ring and o-rings valve lash .003 2)What is the low rpm (idle) it should run 3)The low rpm that it will go and still increase rpm smoothly is 2600 to 2750 4)The max rpm is 7400 to 7550 I would think it shoud turn at 9000 to 9500 rpm and idle at 2500 to 2600, been thinking that I might have the cam retarded 1 tooth thats for low rpm and fair idle
Posted on: 8/11/2009 1:37 PM by Author "nextofkin" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=9007836

RE: Welcome to Club SAITO !
I have a .72 - .82 - 1.20 - and a 1.25 having trouble with the 1.20 geting to idle thought that some of you might have some idea
Posted on: 4/8/2009 1:23 PM by Author "nextofkin" in the forum "Glow Engines"
http://www.rcuniverse.com/forum/fb.asp?m=8661476

Luan Plywood P-51 Mustang With Ryobi
) I thought some one else could help me or know of the web site Thanks nextofkin
Posted on: 6/10/2008 4:21 PM by Author "nextofkin" in the forum "Giant Scale Aircraft - General"
http://www.rcuniverse.com/forum/fb.asp?m=7603832

luan plywood P-51 Mustang with Ryobi
) I thought some one else could help me or know of the web site. Thanks nextofkin
Posted on: 6/10/2008 4:00 PM by Author "nextofkin" in the forum "Scratch Building, Aircraft Design, 3D/CAD"
http://www.rcuniverse.com/forum/fb.asp?m=7603736