RE: Nemesis questions
you can easily take off the engine without taking off the head. you can unmount the engine without any problems ( i think). about the gear mesh, just run a piece of paper between the gears. the paper should fold and not torn. hope it helps.
Posted on: 10/30/2007 9:25 AM by Author "nma3" in the forum "CEN Racing"
http://www.rcuniverse.com/forum/fb.asp?m=6557918

RE: NX-15 Q
it isnt ripped. to make it more snugly fit, i fitted the exhaust port groove with silicone rubber before inserting the gasket. today i run my CT5, and now get a small idea. holding the car in one hand while revving it up, i noticed when i open the throttle, some smoke comes out of the exhuast port while some come out of the pipe itself. i rechecked the exhaust gasket and made sure it isnt not ripped and sure its fit and perfectly smooth but cant understand why in the world it keeps on puffin smoke in the port while revving...geeze, guess i need to change another gasket.
Posted on: 10/25/2007 3:28 PM by Author "nma3" in the forum "CEN Racing"
http://www.rcuniverse.com/forum/fb.asp?m=6537627

RE: ADVICE NEEDED PLEASE
hi billie, have you properly broken your engine? also, you say its over reving without the wheels moving, lift the truck and see if the propeler shafts are rotating, if props rotating but the wheels arent, check that linkage there, there might be loose screws.
Posted on: 10/24/2007 4:45 PM by Author "nma3" in the forum "CEN Racing"
http://www.rcuniverse.com/forum/fb.asp?m=6533490

NX-15 Q
hi, just bought a CT5, broke the engine NX-15 properly then tuned it, after then i noticed leaks of oil coming from the pull starter. i retightened the pullstarter mechanism, but still oil leaks out. checked the O-rings, seems OK and now used some thin gasket on the mechanism but still out of luck. i cant overtighten the bolts (phillips screws) 'cause the screw head seems to give way (or i might not pull it out later) and i cant change the philip screws with hex (hex head wont fit into the hole). am i missing something here? tips will be appreciated, thanks!
Posted on: 10/24/2007 4:10 PM by Author "nma3" in the forum "CEN Racing"
http://www.rcuniverse.com/forum/fb.asp?m=6533346

RE: Dual Steering Servo Mod By The Real Dogman!!
now i got it! nice job!
Posted on: 10/24/2007 3:43 PM by Author "nma3" in the forum "CEN Racing"
http://www.rcuniverse.com/forum/fb.asp?m=6533199

RE: Things you say after crashing
if hundred spectators watching: good thing that was a cheap crap if alone: good thing nobody's watching!
Posted on: 10/24/2007 2:59 PM by Author "nma3" in the forum "RC Humor"
http://www.rcuniverse.com/forum/fb.asp?m=6533016

RE: Kyosho Nexus .30 parts
clutch shoes, liner, tail sliding pitch lever , mast...how?
Posted on: 5/9/2007 6:13 PM by Author "nma3" in the forum "Kyosho Helicopters"
http://www.rcuniverse.com/forum/fb.asp?m=5833278

RE: rotor blade balancing
i have done as ian instructed but still there's that out-of-track.ive notice that a single turn of the snap-on-ball joint has a great effect in such a way that half a turn of a joint can reverse that tracking of both blades. can somebody please explain this phenomenon?
Posted on: 5/4/2007 3:19 PM by Author "nma3" in the forum "Kyosho Helicopters"
http://www.rcuniverse.com/forum/fb.asp?m=5811175

RE: Kyosho Nexus .30 parts
yes i do. my problem here is only a few shops sells kyosho parts here in SEAsia right now.im wondering if shipment here from the west is practical.what do you think?
Posted on: 5/4/2007 2:38 PM by Author "nma3" in the forum "Kyosho Helicopters"
http://www.rcuniverse.com/forum/fb.asp?m=5811046