|
RE: E Flight F-86 Sabre
Thank you for the post wind junkie,much appreciated,didn't want to disconnect anything and end up with a problem!! :-) Thanks again. Regards OMRA
Posted on: 2/20/2012 12:49 PM by Author "omra"
in the forum "Electric RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10967818
RE: E Flight F-86 Sabre
Thankyou mike.So just pull out the red wire of the speed controller yeah,will I still need to disable the BEC?
Posted on: 2/19/2012 4:45 AM by Author "omra"
in the forum "Electric RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10965588
E Flight F-86 Sabre
?? Any help much appreciated. Regards OMRA
Posted on: 2/19/2012 4:03 AM by Author "omra"
in the forum "Electric RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=10965560
E flight Blade SR
Hi guys,after sum help please,I just purchased a Blade SR without the receiver.I have put the spektrum Ar8000in it,just to test it all works and the gyro constantly flashes? any ideas or have i plugged the servos in the wrong locations on the receiver,does any one have picture of there setup?and do all the leads need to be connected? Any help much appreciated. Regards omra
Posted on: 11/6/2011 6:34 AM by Author "omra"
in the forum "E-Flite Helicopters"
http://www.rcuniverse.com/forum/fb.asp?m=10799112
RE: OMRA offshore powerboat race Brixham-Torquay
Thanks,the aeromarine apache is a fantastic hull,ideally suited for racing on the sea!!
Posted on: 9/20/2011 1:56 PM by Author "omra"
in the forum "Speed - RC Nitro Boats"
http://www.rcuniverse.com/forum/fb.asp?m=10726191
RE: OMRA offshore powerboat race Brixham-Torquay
http://youtu.be/ryS8AbJ18QE Return leg back to Brixham. Regards OMRA
Posted on: 9/20/2011 12:45 PM by Author "omra"
in the forum "Speed - RC Nitro Boats"
http://www.rcuniverse.com/forum/fb.asp?m=10726096
OMRA offshore powerboat race Brixham-Torquay
http://youtu.be/AgnjXg3glkw Offshore powerboat race at Brixham.Aeromarine Apache,cmbRs91
Posted on: 9/20/2011 12:43 PM by Author "omra"
in the forum "Speed - RC Nitro Boats"
http://www.rcuniverse.com/forum/fb.asp?m=10726086
Venom King of Shaves P1
I see this new boat on Venoms website,Does anybody have one? Or know what it runs like?? I havent come across any other info/pics of this boat,only whats on their website. : ( Regards OMRA
Posted on: 9/19/2011 11:27 AM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=10724240
RE: ParkZone Micro Mosquito!!!
Hi guys. Well,the mosquito came home yesterday from als hobbies,and must say what a cracking job parkzone have done with this model! Looks absolutely superb.Maiden flight last night at our indoor club and it flew like it was on rails.Only criticism is the charger. Regards OMRA
Posted on: 3/20/2011 12:58 AM by Author "omra"
in the forum "Electric Indoor & Micro RC Flight"
http://www.rcuniverse.com/forum/fb.asp?m=10411012
RE: Gas boat lakes in the UK
bryn bach park is another one,In wales between abergavenny and merthyr tydfil.Go on OMRA website,should be model boat clubs on there.
Posted on: 7/27/2010 12:40 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9891733
RE: Racing at sea
I mean by taking the engine out of the boat.like mart said,general maintenance is the key at the end of the day.We have been running offshore races for many years and not had any problems.
Posted on: 6/12/2010 2:25 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9798353
RE: Kyosho Edge 540 Red Bull Air Race series
Edge 540 (Peter Besenyei) Red Bull Air Race Championship from Kyosho ARTF 1/6 Scale Electric For the world of aerobatic/3D planes, Kyosho has produced a phenomenal 50 class EDGE 540! The left and right halves of the main wing are attached to the fuselage with a light hollow tube so the fuselage doesn't need to be cut. In addition, film on the rear of the fuselage works as stringers to create a lightweight structure. All bulkheads have been computer designed to be as light as possible while still remaining strong. All pieces are cut to lock with each other during factory assembly creating greater strength and consistent quality from plane to plane. If you are looking for the best 50 class Edge, look no further than Kyosho! Features Left / Right halves of main wing are attached with a hollow tube into the fuselage. By removing the cockpit, the wings are then held in place by rubber bands. Shares the same swept trailing edge as the original EDGE 540 and reproduces the same excellent agility and stall characteristics for sharp forward penetration. Factory-assembled balsa fuselage covered in film for a professional finish. Only a short time needed to get flight-ready. Excels at true acro/3D performance due to mid-wing design. No cuts in the fuselage for the attachment of main wing halves results in stronger fuselage structure. Film down the back of the fuselage works as stringers for a lightweight fuselage structure. FRP cowling is pre-painted for true scale appearance. No painting required. Push / Pull wire linkages used for the rudder results in sure control of the yaw axis. Moving tail gear also features shock-absorbing mechanism for safe and reliable taxiing. Factory-assembled balsa fuselage covered in film for a professional finish. Only a short time needed to get flight-ready. Produces the true acro performance of real mid-wing airplanes. Pre-painted FRP cowl. High level of scale detail without the headaches. Wire linkages (included) used for the rudder results in linear control of the yaw axis. Supra Power Brushless Motor with top efficiency Supra Power Lithium Polymer Battery 90% Pre Build Ready to fly within a few minutes Uncomprimised aerobatic flight performance Easy Handling on ground and Air Required Accessories (not included) 4 Channel Radio Transmitter and Receiver, 11.1v 1800-2100 MAh Lipo & charger Specifications Wingspan 1.215mm Length 1.160mm Weight 1.020g approx 1200kv motor included - Speed Controller 30A included - 4 servos included and fitted RC Functions Elevator, Rudder,Aileron, Motor
Posted on: 5/24/2010 1:01 PM by Author "omra"
in the forum "ARF or RTF"
http://www.rcuniverse.com/forum/fb.asp?m=9755920
RE: Kyosho Edge 540 Red Bull Air Race series
Taken from Sussex model centre. Edge 540 Red Bull Air Race Series (Kirby Chambliss) from Kyosho 1/5 Scale IC For the world of aerobatic/3D planes, Kyosho has produced a phenomenal 50 class EDGE 540! The left and right halves of the main wing are attached to the fuselage with a light hollow tube so the fuselage doesn't need to be cut. In addition, film on the rear of the fuselage works as stringers to create a lightweight structure. All bulkheads have been computer designed to be as light as possible while still remaining strong. All pieces are cut to lock with each other during factory assembly creating greater strength and consistent quality from plane to plane. If you are looking for the best 50 class Edge, look no further than Kyosho! Features Left / Right halves of main wing are attached with a hollow tube into the fuselage. By removing the cockpit, the wings are then held in place by rubber bands. Shares the same swept trailing edge as the original EDGE 540 and reproduces the same excellent agility and stall characteristics for sharp forward penetration. Factory-assembled balsa fuselage covered in film for a professional finish. Only a short time needed to get flight-ready. Excels at true acro/3D performance due to mid-wing design. No cuts in the fuselage for the attachment of main wing halves results in stronger fuselage structure. Film down the back of the fuselage works as stringers for a lightweight fuselage structure. FRP cowling is pre-painted for true scale appearance. No painting required. Push / Pull wire linkages used for the rudder results in sure control of the yaw axis. Moving tail gear also features shock-absorbing mechanism for safe and reliable taxiing. Factory-assembled balsa fuselage covered in film for a professional finish. Only a short time needed to get flight-ready. Produces the true acro performance of real mid-wing airplanes. Pre-painted FRP cowl. High level of scale detail without the headaches. Wire linkages (included) used for the rudder results in linear control of the yaw axis. ARF Includes Engine mount 260cc Fuel tank Divided Main Gear Moving Tail Gear (with shock absorbing function) Decals Tyres Linkage Parts - including wire linkages for rudder. Required For Operation (Not Included) R/C System / 4-ch, 5-servo R/C system for airplanes Engine / 2-cycle .46`.50, 4-cycle .52`.63 Propeller / D12~P6`D13~P6 Spinner (57mm) Fuel, Engine Starting Equipment Specifications Wing Span 1.400mm Length 1.360mm Wing Area 36.8 dm2 Weight 2.450g approx Engine required GP 2 ST 46-50 4 ST 52-63 RC Functions Elevator, Rudder Aileron, Engine
Posted on: 5/24/2010 12:58 PM by Author "omra"
in the forum "ARF or RTF"
http://www.rcuniverse.com/forum/fb.asp?m=9755914
Kyosho Edge 540 Red Bull Air Race series
Has anybody seen these two new planes by kyosho?? they look real nice!! Ones electric (peter besenyei)and ones nitro(kirby chamblis) May have to invest [:D] With a smoke system installed that would be the icing on the cake!! Not sure how to link the web page.They are on sussex model centre U.K website home page.
Posted on: 5/23/2010 8:08 AM by Author "omra"
in the forum "ARF or RTF"
http://www.rcuniverse.com/forum/fb.asp?m=9753018
RE: My parkzone HABU
Sorry for the mix up guys,they are 3200milliamp,typing error on my part,sorry.Well tried it again today,no problems at all.Must have been a charge error,although charger said it was complete![8|]Thanks for the input guys. Regards OMRA
Posted on: 5/19/2010 3:36 PM by Author "omra"
in the forum "Electric RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9745038
RE: My parkzone HABU
they are 2300 packs.havent had a problem till today.Possibly is caused by charger.Will try again tomorrow with another charger and see if that helps.
Posted on: 5/18/2010 5:30 PM by Author "omra"
in the forum "Electric RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9742860
RE: My parkzone HABU
Putting between 1.5 and 2 mili amps.
Posted on: 5/18/2010 5:17 PM by Author "omra"
in the forum "Electric RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9742833
RE: My parkzone HABU
battery and charger. Regards Omra
Posted on: 5/18/2010 1:24 PM by Author "omra"
in the forum "Electric RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9742323
RE: My parkzone HABU
customer.[:D] Regards OMRA
Posted on: 5/17/2010 1:36 PM by Author "omra"
in the forum "Electric RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=9739719
RE: My 2007 Miss Beacon Plumbing hydroplane project
She`s come out really well!!! great work!! I still have a few of the smaller decals to get made on mine.Just havent had time!! Congratulations on fine job. Regards OMRA
Posted on: 5/1/2010 8:11 AM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9701934
RE: Racing at sea
Usual maintanance really.strip engine out soon as racing finished,use fresh water(bottled water) through water jacket and lines,clean flexi shaft (WD-40)spray on running gear aswell,till I get home,then polish everything from hull to running gear.oil up engine with after run and thats it really.As long as you wash the salt off you wont get a problem. Fuel I use is Duraglo 10%.That 20min run is about quater of a gallon on the rs91.Half hour run then its half a gallon!! Them nitros do like there fuel!!! £13 a gallon!!
Posted on: 4/26/2010 5:43 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9690803
RE: Racing at sea
More rough racing
Posted on: 4/26/2010 2:08 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9690350
RE: Racing at sea
Some more
Posted on: 4/26/2010 2:03 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9690333
RE: Racing at sea
website...OMRA Offshore Model Racing Association. Regards
Posted on: 4/26/2010 1:55 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9690317
RE: Racing at sea
A few more
Posted on: 4/26/2010 1:46 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9690304
RE: Racing at sea
Thanks!!.Yeah it was really rough.Had a fantastic day
Posted on: 4/26/2010 1:36 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9690287
RE: Racing at sea
A few more
Posted on: 4/26/2010 1:34 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9690278
RE: Racing at sea
A few more
Posted on: 4/26/2010 1:19 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9690246
Racing at sea
Hi guys. It was our first offshore race yesturday at Torquay,here in the U.K.Course was just over 5miles,on the sea.Finishing time was about 20mins to complete. Just thought I would share a few pics of me and my dad racing a Aeromarine Apache,CMB 91rs.
Posted on: 4/26/2010 1:16 PM by Author "omra"
in the forum "Speed - RC Gas Boats"
http://www.rcuniverse.com/forum/fb.asp?m=9690240
RE: BAJA TIME!!!
Thanks for the comments guys. The arms are made by fast lane.All brought from DDM.They fit perfectly,as did everything else.Got a new body shell,high response clutch,carbon rear mount/engine mount and a alloy gear cover.Post pics later. Regards OMRA
Posted on: 4/20/2010 12:12 PM by Author "omra"
in the forum "RC Giant Scale Cars"
http://www.rcuniverse.com/forum/fb.asp?m=9675342
| 
