RE: Volcano 2 speed trans....
yes you can, but i would suggest you get a direct drive tranny with the 13 tooth clutchbell, this can be purchased as a set from somewhere, i think rufaster might have it. it will give u both better top end and low end, where as the 2 speed will give you better high end but less low end power
Posted on: 6/1/2009 9:56 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8817972

RE: Landslide Engineering Requests
yup thats is true, good point
Posted on: 5/29/2009 4:07 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8809364

RE: Landslide Engineering Requests
thicker alluminum shock towers on the landslide if that hasnt already been fixed cause i know that was fixed for the 21 series
Posted on: 5/28/2009 2:05 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8806222

RE: Video's of Jump contest Winner!!
landlide, and landslide 21
Posted on: 5/28/2009 2:03 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8806217

RE: Video's of Jump contest Winner!!
if u just want to see the vids check out youtube. i have won 2 contests just check out perhamrocks on youtube
Posted on: 5/26/2009 9:43 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8801210

RE: support for vortex ss??
its so new that their just arent any vids out there yet
Posted on: 5/26/2009 9:39 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8801195

RE: Volcano SV - Default Factory Settings
[quote]ORIGINAL: chevyderek72 The high speed is the tall one in the gold sleeve, turn that in all the way, just till snug not tight or you'll break it. Then the low speed needle is on the side of the carb, the side that rotates (opens). Set that at flush with the collar, then the idle screw is right in front of the carb. Make sure you have about a 1mm opening in the carb. Those are base settings, if you ever get outa wack or something go back to those settings and tune from there. Do you know how to tune? [/quote] make sure u turn the high speed needle back out 2 1/2 turns after u turn it all the way down. i know thats what u ment to say chevy
Posted on: 5/21/2009 11:38 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8789071

RE: Sh .18 not working
check to make sure all of the needles are set to factory settings, if they r, maybe try leanin the low speed a little bit, cause it sounds like you have everything else set up properly
Posted on: 5/21/2009 11:35 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8789062

RE: broken drive shaft
ya i did that to my volcano too, but that was because i was only running rear wheel drive cause i lost a dogbone
Posted on: 5/21/2009 11:28 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8789045

RE: landslide front hub
i believe there is a grub screw inside of there that u have to take out
Posted on: 4/28/2009 12:07 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8722550

Aftershock Parts?
do you have them in yet? i know most of them are probably interchangable with the landslide, but i think i'd like to buy some aftershock tires for my landslide.
Posted on: 4/24/2009 5:58 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8712423

RE: spur gear
cut a piece of paper to width so it can be slid between the spur gear and clutchbell, loosen all of the motor mount screws on the underside of the chasis and slide the push the engine over tight against the piece of paper and spur gear. tighten the screws and pull the paper out. the gears should not bind when they are turned.
Posted on: 4/24/2009 5:53 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8712415

RE: spur gear
yup, exactly what firebird said.
Posted on: 4/24/2009 9:35 AM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8711156

RE: traxxas 3.3
check out sh engines, they have some really nice .21's, you can get the sh .21 p3 from redcat in the engine replacement program for somwhere around $60 i'm guessing, but i don't think the p3 is going to have as much power as the traxxas 3.3
Posted on: 4/23/2009 9:29 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8710104

RE: 3.2 tires
might want to upgrade to thicker drive shafts and drive cups too cause the big wheels and the bigger engine is going to put lots of stress on that drive train, but you can sure try it
Posted on: 4/22/2009 9:00 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8706728

RE: Sh 18 Rotostart
it sounds like ur engine is just flooded and ur drill doesnt have enough power to turn it over
Posted on: 4/22/2009 8:56 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8706718

RE: 3.2 tires
engine will bog down to from the large tires
Posted on: 4/21/2009 9:42 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8703511

RE: t-maxx shock mod
hope this helps
Posted on: 4/21/2009 9:35 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8703463

RE: new wheels
didn't he turn one into an all out tsunami utrawide too pede?
Posted on: 4/17/2009 10:16 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8691584

RE: new wheels
i remember i while back some guy converted his buggy into an ultrawide and i think he figured it cost him about $600 after he was all done
Posted on: 4/17/2009 9:10 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8691370

RE: new wheels
if it has the two speed yes you'll need a new setup, maybe the direct drive package would be good. if it is a single speed, it probably would just need a different clutchbell
Posted on: 4/16/2009 9:44 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8688357

RE: yeah! new shocks
[quote]ORIGINAL: jcon82 just scored a set of the grey t-maxx shocks on ebay for $19.95! dows anyone have any tips for setting these up on my sv? like what kind of oil, spacers or if the sv ball screws will work with them? if i keep this up i'm gonna have vx powered t-maxx with crappy electronics before i know it[:D] [/quote] they will just snap on if u use the spacers provided and if u have long enough screws, but u will have to sand down the reciever box where the screw holds it down and place a bolt through the end of the reciever box, otherwise that one shock will rub.
Posted on: 4/15/2009 3:05 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8684319

RE: Jumped Landslide, need help!!!!
all u need is the rear lower hinge pin, which is part #60072 just search for that part number on the redcat site, or any other redcat dealer's site the part u need is what u called the "tony bar" it's what allows the lower suspension arm to pivot up and down and hold it in place
Posted on: 4/14/2009 9:03 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8681981

RE: help?
sounds like ur low speed needle is too rich. lean it out and that should also help ur idle along with the idle screw
Posted on: 4/11/2009 10:50 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8672253

RE: actual temp?
200 - 215 is probably right for the idle temp after then engine has been warmed up, but it should be around 260 at it's top rpm's
Posted on: 4/10/2009 10:41 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8669427

P6 or P8 mod?
Is there one of these available for the Sh PT21 P3 engine that comes in the landslide x21? I tried looking on SH's website, but couldn't even find that exact motor. Is there a different brand that would fit?
Posted on: 4/10/2009 9:26 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8669191

RE: Volcano
it will go between 30 or 40, depending on what model u got
Posted on: 4/10/2009 9:20 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8669178

RE: Landslide 2 speed
[quote]ORIGINAL: Landslide Bill WNY You bet Iwill !! Now will I have to adjust the shifting on it to ? [/quote] It might be ok, just run it and check. Then adjust it to how you like it if u don't feel it shifts at a good point
Posted on: 4/8/2009 10:33 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8663214

RE: hpi clutchbell
the direct drive is geared differently then the stock tranny, and that is why the kit comes with 13 tooth clutchbell, if a 17 fits in their you will loose some bottom end power
Posted on: 4/8/2009 10:30 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8663199

RE: Landslide 2 speed
yes re-mesh it to make sure u dont strip a spur gear.
Posted on: 4/8/2009 1:27 PM by Author "perhamrocks" in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=8661491