|
RE: High idle with brake on throttle back
how big is your carb opening?
Posted on: 2/9/2008 7:57 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=7050218
RE: How does motor attach to pull start?
i learned this one the hard way too. you would think redcat would show the bearing in the manual but they dont. Its not a cheap part either to be throwing away with the broken pull starter like i did. Maybe redcat could do a revision to their manual's and add a note reminding you of the one way bearing packed into the pull starter.
Posted on: 1/6/2008 2:29 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6863626
RE: Clutch Bell
it goes in the same way but i had to add 2 5x10x.5 HPI washers to the outer set because the HPI clutch wiggles a little with the stock set of bearings and washers. Hope that helps.
Posted on: 12/2/2007 11:23 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6706500
RE: volcano pull start
sounds good. i just went ahead and ordered a new pull start from clermont, hopefully that comes with the screws and i dont even have to deal with it.
Posted on: 11/24/2007 5:40 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6667451
volcano pull start
So all 4 screws in my pull start backed out on thanksgiving and i wanted to know if anyone knew what size they were. The manual doesn't give a size and i would rather go to my lhs or lowes and get new ones. Thanks for any help.
Posted on: 11/24/2007 4:22 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6667181
RE: Volcano SV problem
i need the those and hex's. the hex's are torn up where the other brand axles werent holding them on tight
Posted on: 11/15/2007 8:58 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6630727
RE: Volcano SV problem
hey clermont.... i dont see the wheel hex's on your site. do you carry them?
Posted on: 11/15/2007 8:52 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6630697
RE: Volcano SV problem
all stock, only thing i did was put the front shock mounts on the lower most outer hole and the back in the upper most inner hole makes it look like a trophy truck. really it was a compression wheelie, he came off a little hill and hit the throttle and it brought the nose right up.
Posted on: 11/15/2007 8:39 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6630640
RE: Volcano SV problem
thanks guys, feel kinda stupid cause that was the only part i didnt check. well it was a blast for the 3 minutes my buddy was hammering on it. he got it to stand up and rode a wheelie for about 5 feet, wish i would have had the camera cause it was sick.
Posted on: 11/15/2007 8:23 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6630548
RE: Volcano SV problem
so i think i know the prob. i bought some non redcat drive cups and they were round all the way instead of the flat spot on the redcat ones. so they spin freely. so i guess i need to order some new drive cups
Posted on: 11/15/2007 8:15 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6630514
RE: Volcano SV problem
thanks bro, will let you guys know if i get her going
Posted on: 11/15/2007 8:01 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6630457
RE: Volcano SV problem
where is the slipper clutch? I'll check the grub screws too
Posted on: 11/15/2007 7:57 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6630436
Volcano SV problem
So i took my truck out today and after about 3 mins it just rolled to a stop even though i was on the gas. Now when i pick it up and hold it and give it gas the tires turn and everything is good. When its on the ground though you can pin it out and it wont budge. Thought maybe it was the clutch but the spring is good and like i said it works fine when the wheels arent touching the ground. any advice? please help....
Posted on: 11/15/2007 7:47 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6630389
RE: is the sv good
Yeah its a tough little truck. I recomend upgrading the shocks to the aluminum ones though. I bent or broke all eight in the first two weeks i had it. you can get the redcat ones or traxxas t-max shocks work too. Upgrade the pipe as well to an aluminum one. i broke the OEM pipe and noticed a little power gain with the aluminum one. good luck man
Posted on: 10/1/2007 4:43 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6436560
RE: Redcat Racing Volcano Thread
I'm new to this sport and recently bought a Volcano SV and LOVE IT!!! After breaking in the engine and getting the concept of these powerful little trucks i decided i would see what it could do in the air. I was hitting a little 8 foot gapper and clearing it but on my last attempt things went terribly wrong. I broke the left front lower arm, broke the support piece on the cheap stock exhaust, and bent the back left axle. My question is when i went to pull the axel out it wouldn't budge from the rear upright even with the two grub screws removed, how is this accomplished? My other question was if anyone had any good suspension setups for max travel and landing? Thanks, aaron
Posted on: 9/17/2007 5:22 PM by Author "vtrebel"
in the forum "Redcat Racing Support"
http://www.rcuniverse.com/forum/fb.asp?m=6379888
| 
