RE: Warbirds and classics over the Midwest. (Fond du Lac)
opie from minnesota I believe owns the tracker. Carl B built it maybe?
Posted on: 8/21/2012 6:26 PM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=11201507

RE: what engine is this?
I found out that this is a Sachs engine 75cc, with the center pin of the battery jack being positive. Thats what I needed to know. Thanks for your help guys.
Posted on: 7/24/2012 1:47 PM by Author "warbirdav8r" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=11167584

RE: what engine is this?
thanks for the info..
Posted on: 7/23/2012 5:41 PM by Author "warbirdav8r" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=11166510

RE: what engine is this?
I found a ph. number on a sticker on the case, Try and see what happens. I dont know if It runs well or not as it doesn't have a muffler. Without knowing what it is I dont want to get a muffler I cant use..
Posted on: 7/23/2012 4:30 PM by Author "warbirdav8r" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=11166396

RE: what engine is this?
carb says 21-85 Walbro... Doing a c.i.d. formula of the internet, bore x bore x stroke x .7854 it comes to approx 5.0 cid. Hard to measure real good but I used conservative measurements. Dont have a clue as to brand though. Don't know how to get a muffler for it? Dont know what it is. Approx 40mm across the muffler bolt hole center to center..
Posted on: 7/22/2012 7:33 PM by Author "warbirdav8r" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=11165178

RE: what engine is this?
I've had g23's, This is alot bigger than a 23. Thanks though.
Posted on: 7/22/2012 6:38 PM by Author "warbirdav8r" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=11165080

what engine is this?
I aquired this from a friend. Don't know much about it. Looks like at least 75cc but dont know what brand etc.. Has Ralphs ign. on it I believe. Also does anybody know if the center pin on this speaker jack type of plug for the Ign.battery is pos. or neg? Any info is helpful, thanks, Dave.
Posted on: 7/22/2012 4:52 PM by Author "warbirdav8r" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=11164924

RE: Palmer Plans F9F Cougar
Looks great Rich! I didn't know you were working on that one. Hope to see you and chuck at cards in june. Bring that with you, maybe we can do panthers and cougar.. Dave.
Posted on: 3/26/2012 2:09 PM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=11015995

RE: Painting and balancing a prop..
aircraftinternational.com , click on media then on prop balancing video. Paint it as you wish and check it again if needed.
Posted on: 8/16/2011 6:57 PM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=10673730

RE: P-61 Refurb-10 yr old servos ?
Greg was a JR guy in 2000 and flew a dauntless. That p-61 is a year or 2 newer than that if it matters to you.
Posted on: 1/2/2011 6:08 PM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=10235153

RE: 2010 Indiana Warbird
Jack, Thanks for the pics. Glad you Michigan guys could come fly with us. The weather will surely be better next year.
Posted on: 9/7/2010 5:16 PM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9986650

RE: P-47 ,,, 3 view - photo help
Try the guys on armyairforces.com.
Posted on: 1/4/2010 5:49 AM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9385347

RE: ROAD TRIPS: 2009
The other one was Chuck Hamilton.
Posted on: 12/20/2009 10:42 PM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9347430

RE: ZIROLI F9F PANTHER BUILD
The Blue and Yellow scheme was used on target tug aircraft. High vis hoping to not get shot at.
Posted on: 11/21/2009 6:08 AM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=9269427

RE: Nose Wheel Steering...
plug your nosewheel servo into the rudder port on your receiver and mix the rudder to it if you have an extra channel. You can use the dual rate rudder switch then if you want and not affect the rudder. It makes trim on your steering easy also as it's now on your rudder trim. I read this in a Jim Hiller article once and it works great.
Posted on: 5/31/2009 7:27 AM by Author "warbirdav8r" in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=8813143

RE: Ziroli 92" P-47 Paint Help
Testors model masters series has all the colors you need. They are the right colors.
Posted on: 7/19/2008 7:03 PM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=7749355

RE: G-62 break-in
I've run lawnboy 32:1 in mine for 15yrs. Still runs great. Set it just a tad rich and fly at first. I havent bench run any of them.
Posted on: 7/11/2008 6:09 AM by Author "warbirdav8r" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=7718119

RE: Zen G26 Carb Adjustments - Help
the guys that are telling you to solder the tube on are dead on. I had this same issue on my b-25 this summer. Also, I picked up 800 rpm with the stock velocity stack on, as opposed to off. I had engine out flights and etc.. until I these changes were made..
Posted on: 7/4/2008 7:18 AM by Author "warbirdav8r" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=7692839

RE: FUNSONIC turbine feedback
40 flights on mine now.I had some issue with the propane valve early on, but robart took care of it and it runs great now. Starts easily etc...
Posted on: 4/14/2008 8:07 PM by Author "warbirdav8r" in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=7373832

RE: DA-85 Question or TWo...
I drill a small hole on the back side of the hub, on the light side. Drill it directly across from the heavy point. I use a small piece of music wire and ca it in the hole to even the weight out. If your running prop hubs and not spinners, that velcro strip deal looks pretty bad.
Posted on: 2/15/2008 6:14 AM by Author "warbirdav8r" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=7078367

RE: 12lbs turbine
A ziroli panther is pretty cheap to do and it's scale if that matters to you.
Posted on: 12/23/2007 9:03 AM by Author "warbirdav8r" in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=6794143

RE: New Robart P-47 Arf
The ziroli p-47 plan shows both versions.
Posted on: 11/5/2007 8:58 PM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=6585907

RE: Air valve need help
sound like an ultra precision valve to me
Posted on: 10/23/2007 11:28 AM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=6527746

RE: Ziroli Skyraider
hellcat56, Nice looking raider. I've had a Ziroli raider for 9 years. And your right it is a great flying airplane. I'm interested to know if your tailwheel is from earl aune, or is something you made. They were available from ziroli at one point, very scale but mine never held up very well and I took it out.
Posted on: 9/8/2007 6:04 AM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=6341786

RE: Want to get a jet... where do I start?
A Ziroli panther is the least expensive way to get into a scale jet IMO. It's all wood and not hard to build. You could go with the new Turbinator, also wood, doesn't need a pipe, and it's easy to build. I really like my panther and it is my first jet. You won't go wrong with either one if you don't mind building.
Posted on: 8/23/2007 9:47 PM by Author "warbirdav8r" in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=6279002

RE: Warbirds Over Delaware
INDIANA WARBIRD CAMPAIGN at the ama site in Muncie IN. Giant scale imaa event. Labor day weekend, alot of good planes will be there.
Posted on: 7/13/2007 11:04 PM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=6108586

g-26 props
I have g-26's coming for my b-25. Whats the best prop for this. clearence is pretty close on anything over 17''. Graupner 16-8 3 blade I'm thinking?
Posted on: 7/7/2007 2:14 PM by Author "warbirdav8r" in the forum "Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=6081448

RE: Where have the builders gone?
Doolittleraider, It's the smaller 101'' version. I found a great deal on gear and the ziroli stuff together so I went with that. Thanks for the info.
Posted on: 12/7/2006 6:17 AM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=5085812

RE: Where have the builders gone?
doolittle, I know it's off topic but I'd be interested to know where you got the RUPTURED DUCK art. I'm one of those few who still build i guess and I have a Ziroli b-25 b model almost ready to paint. Ruptured duck is my scheme, I have the in action book but the artwork is really small in the pics. Thanks
Posted on: 12/5/2006 9:56 PM by Author "warbirdav8r" in the forum "RC Warbirds and Warplanes"
http://www.rcuniverse.com/forum/fb.asp?m=5080630

RE: Kentucky Jets 07 Pre-Registration
Dennis, glad to see you finally got rid of your old rig and traded up to such a fine ride. Throw a rope in the cab and i'll be sure you make it down.
Posted on: 11/29/2006 10:46 PM by Author "warbirdav8r" in the forum "RC Jets"
http://www.rcuniverse.com/forum/fb.asp?m=5056273