receiver cutting off under full accleration
hi anyone have problem when you put receiver on and accelarate and the reciver switches off.after disconecting battery and reconecting it, it comes on again but when you give it full throttle the receiver switches off again.anyone got any idea why this is happening . i am using spectrum receiver and mamba esc and mamba max motor
Posted on: 2/22/2009 4:17 PM by Author "zsar1" in the forum "RC Car Radio Equipment"
http://www.rcuniverse.com/forum/fb.asp?m=8505977

jato conversion to sidewinder brushless
hi.could any one tell me what parts(engine mount,pinion,etc) i need to convert my jato to sidewinder brushless.
Posted on: 9/6/2008 6:29 PM by Author "zsar1" in the forum "RC Nitro Stadium Trucks"
http://www.rcuniverse.com/forum/fb.asp?m=7927016

jato wheel hex
hi 1.what parts do i need to change my front bearings to 14mm hex because i want to rotate tires around so they wear evenly. 2. how do slow my diff action there is alot of wheelspining . i have put in 7000 wt oil in diff and my gearing is 24th clutch bell and standard spur.any other suggestions.
Posted on: 8/7/2008 6:01 AM by Author "zsar1" in the forum "RC Nitro Stadium Trucks"
http://www.rcuniverse.com/forum/fb.asp?m=7818780

gearing on hellfire with lrp
hi .i tried to put an lrp 28 with pull start with a 16t clutch bell.but it would noy fit.i also had to use 2 of the purple engine mounting plate so that the engine would sit properly on the chasis.the bottom of the engine is too high.i dont want to grind the bottom because it might ruin the pull start.because on the engine sitting a little higher the 16t wont fit.i have now put the 12t back in.it now stays perfectly meshed without the engine moving.will thelow gearing harm the diffs with the torque of this new motor
Posted on: 12/1/2007 1:12 PM by Author "zsar1" in the forum "RC Truggy"
http://www.rcuniverse.com/forum/fb.asp?m=6699646

airtronics mx 3 fhss -naming vehicles
hi .i have a spectrum radio that i can rename models.i have just bought the airtronics.the instruction manual does not say how to rename model.can iy be done on this radio?
Posted on: 12/1/2007 12:58 PM by Author "zsar1" in the forum "RC Car Radio Equipment"
http://www.rcuniverse.com/forum/fb.asp?m=6699604

1/18 HPI rs4 HELP
Hi .i was thinking of buying HPI 1/18 micro RS4 ARR. It does not come with a motor and esc. I have a team associated XPS MICRO ESC 29136 and associated SUPER 370 MOTOR.the question is 1. will this work with the HPI 1/18 micro RS4 ARR . if yes, will it be underpowered? 2. will the team associated XPS MICRO ESC 29136 work with HPI Modified Motor 45T Micro RS4.will it match perfectly or not? 3.any other mods recommended for this drifter?
Posted on: 11/26/2007 2:47 PM by Author "zsar1" in the forum "1/16th, 1/18th, Mini & Micro RC Cars"
http://www.rcuniverse.com/forum/fb.asp?m=6676249

1/18 HPI rs4 HELP
Hi .i was thinking of buying HPI 1/18 micro RS4 ARR. It does not come with a motor and esc. I have a team associated XPS MICRO ESC 29136 and associated SUPER 370 MOTOR.the question is 1. will this work with the HPI 1/18 micro RS4 ARR . if yes, will it be underpowered? 2. will the team associated XPS MICRO ESC 29136 work with HPI Modified Motor 45T Micro RS4.will it match perfectly or not? 3.any other mods recommended for this drifter?
Posted on: 11/26/2007 2:46 PM by Author "zsar1" in the forum "RC Drifting"
http://www.rcuniverse.com/forum/fb.asp?m=6676239

what other radio will work with spectrum receiver
hi.i have a spectrum transmitter and 3 spectrum receivers.i have a forth and fifth vehicle and the spectrum only has a 3 mode memory.i was thinking of getting the futaba or airtronics 2.4ghz transmitter.they have a 10 mode memory and the spectrum has 3 mode memory.does anyone know which transmitter will work with the other 3 spectrum receivers i have.
Posted on: 7/15/2007 1:48 PM by Author "zsar1" in the forum "RC Car Radio Equipment"
http://www.rcuniverse.com/forum/fb.asp?m=6113859

stinger for picco .26 max
hi .has anyone tried a mip stinger pipe on their revo.i tried it on mine today and it seems better than stock pipe.i don`t know weather to leave stinger pipe or get the t.h.s pipe that everyone talks highly about
Posted on: 4/14/2007 6:00 PM by Author "zsar1" in the forum "Traxxas Monster Truck forum"
http://www.rcuniverse.com/forum/fb.asp?m=5715511

which engine for 3 different vehicles
hi.could anyone give a suggestion as to what engine to put in which specific vehicle.the cars i have is SAVAGE / REVO /HELLFIRE and the motors i have is O.S 18CV-RX /PICCO MAX .26 /WASP.26 /SIRIO 27XL(one theway out cause its compresion is almost going nad idle is not constant/ SH.28 /OFNA HYPER .21. at the moment i have the wasp 26 in my savage and picco max 26 in my revo.i am waiting for my hellfire ss kit to be shipped to me.i am also going to order a buggy.any sugestions
Posted on: 4/14/2007 5:57 PM by Author "zsar1" in the forum "Car Nitro & Gas Engines"
http://www.rcuniverse.com/forum/fb.asp?m=5715503

piccco 26 engine setting
hi can anyone tell me what is factory setting for lsn and hsn(picco 26).i don`t have a manual for this engine .thanks
Posted on: 3/15/2007 5:39 AM by Author "zsar1" in the forum "Traxxas Monster Truck forum"
http://www.rcuniverse.com/forum/fb.asp?m=5563779

sirio 27 one way bearing
hi. can anyone tell me were i can buy cheapest one way bearing for sirio 27 or if there is another bearing that i can use which is cheaper than the sirio one way bearing. another thing is that after every run my bearing does not grip so i have to take out motor and open the roto start up and on the shaft that the one way bearing goes on ,it is full of grease. why is there grease every time i run it .any one got any ideas on how to stop grease coming from engine(i presume) . another thing is that i need a stronger throttle arm hpi 85051 (the l thing that pulls the engine throttle) is there an aluminium one out there
Posted on: 1/2/2007 5:07 PM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=5198561

rubber ballons
hi.i just bought the tamiya rubber ballon.i would like to know if i can put it on my servos to waterproof them.the manual says its for speed control and receiver only.
Posted on: 10/28/2006 5:39 PM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=4926162

RE: wasp 26 engine settings
at the moment i got the hsn at 7 out.and the temperature is about 230 degree.i dont know if it is running rich or weather the temperture of the engine sholud be so high.i `m freightened to lean it cause the engine might get hotter.
Posted on: 10/23/2006 1:52 PM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=4904375

wasp 26 engine settings
can any one tell me the original seting for wasp .26
Posted on: 10/22/2006 1:51 PM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=4900208

26BROKEN WASP .26 CRANKSHAFT
HI . I`VE JUST BROKEN MY CRANKSHAFT ON MY WASP .26 . IT BROKE JUST ABOVE WHERE THE THREADING STARTS.I`VE NOW SHAVED OF THE REMINING PART AND I STOPED AT WHERE THE THRADING STARTS.DOES ANY ONE KNOW WHAT OTHER PILOT NUT WITH A STEM I CAN USE SO THAT I CAN GET MY SAVAGE RUNNING AGAIN
Posted on: 9/30/2006 5:03 PM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=4811788

idle to high
hi.i got a problem when i drive my savage.the problem is that when i`m at full throttle and when i bring her to a stop the idle remains high.then after about 30 seconds she comes to her regular idle.if i put fully throttle she revs up.only when she comes to normal idle then she goes in gear then only can i drive her.many solutions.the spur is tight.could it bee low end needle.the idle is set right but it takes time for her to come doen after a stop.
Posted on: 5/28/2006 6:18 AM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=4324257

reving up
hi.my savage was running just fine with wasp 26 and nova aluminium shoes.then she started reving up.i stripped the clutch and the clutch shoes were melted.i replaced it with a brand new standard clutch shoe.it still is sliping.i tightened the spur gear.and that did not help.any one got any ideas
Posted on: 3/11/2006 4:57 AM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=4019162

wasp 26 needs sealing and what glowplug
hi.do u guys know weather the wasp 26 is sealed from factory or i got to seal it my self.will the savage rooto start fit on it.the instruction says that it will not work.there is always ways of making things work!!!!any one tried it.and whats the best glowplug that works best with this engine.i`ve got os no3 and no8 or will the cold r5 work better.thanks
Posted on: 1/10/2006 1:16 PM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=3756683

wasp 26 or ofna picco 26
hi which will be a better engine to get.i have been to tower hobby website and they say that the ofna 26 picco is for the t-maxx.will it bolt on perfectly on a savage.i also saw that they have a ofna 27 picco.will it fit in a savage.they say that it is suitable for on road racing.will it work on the savage.
Posted on: 12/18/2005 11:07 AM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=3666421

tsias maxima pipe
hi.i`ve been to rchib and i`m interested in maxima pipe.does any one have one?does it increase horse power?does feul still get on the tires?or is it better to get an ordinary in line chrome pipe?
Posted on: 11/19/2005 2:54 PM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=3568092

looking for 1 charger that charges multiple packs at once
hi.i`m looking for a charger that i can charger my glowplug(ni-mh) and 6c batt pack(ni-cd).it has to be versatile cause i`m tired of charging one battery pack at a time.i`ve got a triton charger.the other charges i`m looking at is megatech juicebox2,hi tec cg335,hobbico quick field dc charger mk11,mrc super brain977. i need a charger with 12v input or 220v input.
Posted on: 11/13/2005 1:38 PM by Author "zsar1" in the forum "Batteries & Chargers"
http://www.rcuniverse.com/forum/fb.asp?m=3547848

carburator sticky
hi.can any one give me answers on how to fix my carb. it so hard to pull my slide carb on my sirio 27 .i tried stripping it and putting wd40 in it and even nitro in it but when i put it toegether it so hard to pull.i fear that my servo will break if this continues.any solutions
Posted on: 10/30/2005 10:19 AM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=3504032

RE: mamba break in
thanks for that help.another question is that i noticed that that the power is connected directly to the motor via the switch.if i leave the battery connected with the switch off will the battery get drained out.will it be supplying some power to the motor with the switch off
Posted on: 9/25/2005 12:44 PM by Author "zsar1" in the forum "1/16th, 1/18th, Mini & Micro RC Cars"
http://www.rcuniverse.com/forum/fb.asp?m=3391940

mamba break in
hi.i`ve just bought rc18t and a mamba competition x motor and esc.i`m new to electric cars.i always see these things called LATHES or something of that sort.i haven`t put on the mamba as yet.DO U HAVE TO BREAK IN ELECTRIC MOTORS AS U WOULD BREAK IN A NITRO MOTOR?
Posted on: 9/25/2005 10:55 AM by Author "zsar1" in the forum "1/16th, 1/18th, Mini & Micro RC Cars"
http://www.rcuniverse.com/forum/fb.asp?m=3391649

RE: best upgrade for rc18t with mamba
doesn`t the mamba come with esc????i order one with the complete package (competition x)
Posted on: 9/18/2005 3:00 PM by Author "zsar1" in the forum "1/16th, 1/18th, Mini & Micro RC Cars"
http://www.rcuniverse.com/forum/fb.asp?m=3370144

best upgrade for rc18t with mamba
hi .whats the best upgrdae for my rc18 mt2 .what will be needed to handle the mamba 8000
Posted on: 9/17/2005 4:15 AM by Author "zsar1" in the forum "1/16th, 1/18th, Mini & Micro RC Cars"
http://www.rcuniverse.com/forum/fb.asp?m=3366618

mt2 dif help
hi.i`ve just ordered the heavy duty gears for my diff.the question is that i want to know if i must still use the washers to lessen the play in the diffs
Posted on: 9/14/2005 1:43 PM by Author "zsar1" in the forum "RC Nitro Stadium Trucks"
http://www.rcuniverse.com/forum/fb.asp?m=3358146

RE: easy lower your savage?????
hi.i used 2 of my blk original springs and 2 off a stiffer spring made by rc trix.i cut the 4 original springs with a dremmel tool.i put 2 of the blk cut springs and 2 of rc trix springs in the front and the same in the back.i put 30 weight on all shocks.the front sits a little lower than the back.the idea with the stiffer spring is that it won`t hit the bottom very easy.my savage handles extremely well.it hardly flips when i`m turning at full throttle
Posted on: 8/28/2005 12:34 PM by Author "zsar1" in the forum "HPI Monster Truck Forum"
http://www.rcuniverse.com/forum/fb.asp?m=3306819

mt2 throttle/brake alternative
is there any other way to run the throttle/brake linkages on the servo.i have a rotary carb.the standard throttle linkages stink.can one tried any other way.post pictures if u can and what was purchased
Posted on: 8/26/2005 2:29 PM by Author "zsar1" in the forum "RC Nitro Stadium Trucks"
http://www.rcuniverse.com/forum/fb.asp?m=3301504